Deutschland 07056-9398-0 | Internationale Rufnummer ++49 (0) 7056-9398-0 | Willkommen auf unserer neuen Website! Haben Sie einen Fehler oder ein Problem entdeckt? Bitte melden Sie es hier.
Particulate-Matter
PM2.5, 0-500 µg/m3, 4-20 mA und 0-10 VDC, Modbus RS-485
- Überwachung der Luftqualität
- Luftreiniger
- WELL Building Standard
Particulate-Matter
Von
Produktübersicht
- Genauigkeit ± 10 μg/m3
- Genauigkeit Detail +/- 10 % Messwert bei 100 ~ 500/600 μg/m3 bei 25°C/50 % rF
- Anwendungen Luft- und Klimatechnik, Bauwesen und Zollstandhaltung, Umweltüberwachung
- Zulassungen CE, RoHS2
- Datenschnittstelle Modbus RTU, RS485
- Elektrischer Anschluss Schraubklemme
- Elektrischer Ausgang 4 bis 20 mA, 0 bis 10 Vdc
- Gehäusematerial ABS-Kunststoff
- Gehäuse-Nennwerte UL94 V-0
- Eingangstyp Lüfter
- Schleifenwiderstand, max. 4-20 mA: maximal 500 Ohm (Standard)
- Option für Materialkonstruktion keine
- Betriebsfeuchtigkeit 0 bis 95 % relative Luftfeuchtigkeit, nicht kondensierend
- Betriebstemperatur, max. 122 °F
- Betriebstemperatur, min. 32 °F
- Schutz IP30 (Raum)
- Relaisausgang 3 A bei 30 Vdc, 3 A bei 250 Vac
- Auflösung 1 µg/m3
- Reaktionszeit Im Dauerbetriebsmodus, Abtastzeit <1s, Ansprechzeit <10s
- Sensortyp Laser-Partikelsensor
- Serien-ID Particulate-Matter
- Gerätelebensdauer MTBF von mehr als 3 Jahren im Dauerbetrieb, Lebensdauer bis zu 8-10 Jahren im Automatik- (intermittierenden) Betriebsmodus
- Lagertemperatur, max. 70 °F
- Lagertemperatur, min. -30 °F
- Versorgungsstrom 50 mA
- Versorgungsspannung 16 bis 28 VAC, 16 bis 35 VDC
- Anzugsmoment 0,45 lb-in (0,5 Nm) Nennwert
- Auslösepunkt Hinweis Relais-Auslösepunkt: 100 (Werksseitig eingestellt), benutzerverstellbar
- Aufwärmzeit 15 Minuten
- Gewicht 270 g
- Drahtstärke 22 bis 16 AWG
Supported Applications
The ACI PM series transmitters are designed to measure particulate matter (PM) concentration in the air. The product overview identifies specific measured substances including smoke, smog, bacteria, fine dust, and liquid droplets. These units utilize a laser particulate matter sensor operating on a laser scattering principle with fan sampling.
Operating Conditions & Performance
The series supports two measurement ranges: particles less than 2.5 µm in diameter (PM2.5) and particles less than 10 µm in diameter (PM10). The sensor operates via a laser scattering principle with fan sampling.
Power requirements are specified as 24 VDC or 24 VAC. Output signals include 0-10 VDC, 4-20 mA, and RS485 Modbus RTU communication. Electrical connections utilize terminal blocks for 1 or 2 wires per position to allow daisy chaining.
Installation warnings note that performance may decrease in extreme environments such as high humidity, high temperature, excessive dust, or oil mist. The sensor is sensitive to strong light entering the housing and vibration. To maintain accuracy, installation should avoid air registers, diffusers, vents, windows, confined areas (shelves, closed cabinets), heat sources (lamps, radiators, direct sunlight), and wall cavities with unsealed penetrations.
Configuration Options
The series offers configurable output signals and communication protocols. Available outputs include 0-10 VDC on Terminal 3, 4-20 mA on Terminal 4, and RS485 (Modbus RTU). The sensor features two jumper-selectable modes: Normal for continuous monitoring and Auto to reduce measuring time and extend service life; the default mode is AUTO.
Communication parameters are configurable via Modbus registers or menu adjustments:
- Baud Rate: 9600 (default) or 4800
- Parity: None, Odd, Even
- Slave Address: Configurable from 1 to 255 (1-32 recommended)
- Function Codes: Supports 03H/06H; address 0 is for broadcast and 255 (0xFF) for special mode read data
The series supports relay control with multiple modes defined by parameters including Set Point, Dead Band, Actuate Delay, and Restore Delay. Relay activation can be configured to trigger below a set point, above a set point, between high/low limits, or outside high/low limits.
Key Product Differences
The series includes distinct model configurations identified by part numbers PM-D, PM-R, PM-R-LCD, and PM10-D. The PM-ROOM designation is referenced in the product overview for room-based monitoring applications. Physical dimensions vary between housing styles; one configuration measures 4.79" (121.55 mm) height x 3.268" (82.00 mm) width x 0.984" (25.00 mm) depth, while another measures 3.99" (101.353 mm) height x 4.331" (110.00 mm) width x 4.921" (125.00 mm) depth.
Wiring recommendations specify the use of 16 to 26 AWG twisted pair or shielded cable, with Belden 3105 recommended for Modbus communication wiring due to its 120 ohm input impedance. RS-485 networks require daisy chain topology; 'Star' or 'T' wiring is not supported. A termination resistor (120 Ω) controlled by a jumper on J8 is required at the last device in the chain.
PDFs & Handbücher
