Singapore 1800 622 1156 | Intl +65 6415 5353 | Welcome to our new site - found a bug? Please report it here
iNET-600-Series
High Accuracy Direct-to-Sensor USB Data Acquisition System
Models In Stock
- Connects a Computer to Sensors and Controls via Analog and Digital Inputs and Digital Outputs Via Windows® Software
- iNET-601 Provides ±36V Input Bank to USB Electrical Isolation
- iNET-600 Connects I/O Signal Ground to Computer Ground Receives Power from USB Bus
- 16SE/8DI Voltage Input Channels with Extremely Accurate 24-Bit A/D Converter that Supports ±20 mV to ±10V Ranges 4 Digital I/O (4 mA Sink/Source, 0 to 3.3V)
iNET-600-Series
From
SGD
1,397.60
Models In Stock
Product Overview
- Analog I/O Note Analog: Number of Channels: 16 single-ended (SE)/8 differential (DI), A/D Converter: 24-bit when averaging each point for ≥1m sec; and 16 bits when not averaging, Voltage: See voltage accuracy/range charts, , Protected Voltage: ±30 Vdc with power on or off, RFI Filter: 13 KHz RFI filter on ≤ ±150 mV range Digital: Number of Channels: 4 digital I/O (4 mA sink/source, 0 to 3.3V): “0” Input Voltage: 0 to 0.8 Vdc, “1” Input Voltage: 2 to 5.5 Vdc, “1” Input Current: Amps = Vin / 50 kΩ (“1” must drive internal 50 kΩ pull down resistor), Pull-Down Resistor: 50 kΩ ±1%
- CMRR ≥110dB (0 to 60 Hz)
- Common Mode Voltage ±10 Vdc
- Current Measurement Range ±80 uA, ±120 uA, ±500 uA, ±600 uA, ±800 uA, ±1.2 mA, ±2.5 mA, ±12 mA, ±24 mA, 0 to 24 mA
- Data Interface Note InstruNet Software
- Digital Filter Type Elliptic, Chebyshev B, Chebyshev S, or Butterworth
- Digital Input Digital: Low = 0 to 0.8 Vdc
- Digital I/O Note Number of Channels: 4 digital I/O (4 mA sink/source, 0 to 3.3V) “0” Input Voltage: 0 to 0.8 Vdc “1” Input Voltage: 2 to 5.5 Vdc “1” Input Current: Amps = Vin / 50 kΩ (“1” must drive internal 50 kΩ pull down resistor) “0” Output Voltage: <0.7 Vdc @ <2 mA; < 0.9 Vdc @ 4 mA “1” Output Voltage: 2.2 to 3.3 Vdc @ 4 mA Pull-Down Resistor: 50 kΩ ±1% Sink Current: 4 mA
- Digital Output “0” Output Voltage: <0.7 Vdc @ <2 mA; < 0.9 Vdc @ 4 mA, “1” Output Voltage: 2.2 to 3.3 Vdc @ 4 mA
- Height 58 mm
- Impedance Input 100 MΩ
- Input Type Voltage, Thermocouple, Thermistor, RTD, Load Cell, Strain, Potentiometer, Current, Resistance, Flow, Pressure, Digital
- Length 24 mm
- Materials Plastic
- Mounting Place on Desktop, Attach to Wall, or place inside another Enclosure (OEM)
- Number of Channels, Output Digital: 4
- Operating Temperature, Max 70 °C
- Operating Temperature, Min 1 °C
- Output Signal Digital
- Protection Protected Voltage: ±30 Vdc with power on or off
- Pull-down Resistor 50 kΩ ±1%
- Relative Humidity <90% RH, no condensation
- Resistance Measurement Range 1 to 50 kΩ Pot, 0 to 33 Ω, 0 to 100 Ω, 0 to 330 Ω, 0 to 1 kΩ, 0 to 3300 Ω, 0 to 10 kΩ
- Sensor Type Thermocouple Type J, K, T, E, R, S, B, N, C, G, D, 100 Ω RTD, 500 Ω RTD, 1 kΩ RTD, 2252 Ω Thermistor
- Series ID iNET-600-Series
- Storage Temperature, Max 70 °C
- Storage Temperature, Min -20 °C
- Supply Power Note Voltage Reference At Hd44 Connector: 3.30 Vdc (80 mA)
- Supply Power Type DC
- Supply Voltage ± 5 Vdc
- Temperature Measurement Range TEMP LABEL 1 To be Updated
- Voltage Measurement Range ±20 mV, ±40 mV, ±80 mV, ±150 mV, ±300 mV, ±600 mV, ±1.2V, ±2.5V, ±5V, ±10V
- Width 96 mm
Supported Applications
The Omega iNET-600 Series is a high accuracy direct-to-sensor USB data acquisition system designed for laboratory and industrial measurement tasks. The series provides 16 single-ended or 8 differential voltage input channels with a 24-bit A/D converter, enabling the connection of various sensors including thermocouples, thermistors, RTDs, load cells, strain gages, potentiometers, current sources, resistance devices, and direct voltage inputs.
Control is managed via Windows software using analog and digital I/O. The system supports compatibility with Excel, LabVIEW, DASYLab, MATLAB, Origin, C & Visual BASIC software for data logging and analysis applications.
Operating Conditions & Performance
The iNET-600 Series operates within an ambient temperature range of 1 to 70°C (34 to 158°F) with a storage temperature rating of -20 to 70°C (-4 to 158°F). Humidity must remain below <90% RH, no condensation. The unit is powered by +5 Vdc from the USB cable, drawing 255 mA typical (433 mA max).
Measurement ranges span ±20 mV to ±10V with a resolution of 24-bit. Absolute accuracy varies by range and signal averaging time:
- ±10V Range: Accuracy is ±(0.005% + 1569.9 μV) for 0 mSec averaging or ±(0.005% + 271.8 μV) for 1.0 mSec averaging.
- ±5V Range: Accuracy is ±(0.005% + 709.4 μV) for 0 mSec averaging or ±(0.005% + 131.6 μV) for 1.0 mSec averaging.
- ±2.5V Range: Accuracy is ±(0.005% + 374.2 μV) for 0 mSec averaging or ±(0.005% + 69.2 μV) for 1.0 mSec averaging.
- ±1.2V Range: Accuracy is ±(0.005% + 197.3 μV) for 0 mSec averaging or ±(0.005% + 37.2 μV) for 1.0 mSec averaging.
- ±600 mV Range: Accuracy is ±(0.005% + 123.9 μV) for 0 mSec averaging or ±(0.005% + 22.4 μV) for 1.0 mSec averaging.
- ±300 mV Range: Accuracy is ±(0.005% + 90.9 μV) for 0 mSec averaging or ±(0.005% + 15.3 μV) for 1.0 mSec averaging.
- ±150 mV Range: Accuracy is ±(0.005% + 70.4 μV) for 0 mSec averaging or ±(0.005% + 11.4 μV) for 1.0 mSec averaging.
- ±80 mV Range: Accuracy is ±(0.005% + 49.3 μV) for 0 mSec averaging or ±(0.005% + 8.6 μV) for 1.0 mSec averaging.
- ±40 mV Range: Accuracy is ±(0.005% + 32.8 μV) for 0 mSec averaging or ±(0.005% + 6.7 μV) for 1.0 mSec averaging.
- ±20 mV Range: Accuracy is ±(0.006% + 32.1 μV) for 0 mSec averaging or ±(0.006% + 6.5 μV) for 1.0 mSec averaging.
The system provides excitation power of +3.3V ±0.2V (80 mA, 28 mA per sensor max). It includes 4 digital I/O channels capable of 4 mA sink/source at 0 to 3.3V.
Configuration Options
The series is available in two primary configurations: the iNET-600 and the iNET-601. The iNET-601 model offers ±36V input bank to USB electrical isolation, whereas the standard configuration connects I/O signal ground to computer ground.
Physical Specifications
- Housing: Plastic enclosure with dimensions of 58 H x 96 W x 24 mm D (3.784 x 0.924 x 2.286").
- Weight: 454 g (1 lb).
- Connector Type: Hd44 Female Connector.
- Certifications: CE, RoHS.
Sensor Interface Options
The system supports direct connection to sensors via the included instruNet World Software. For thermocouple applications, an iNET-510 wiring box is required due to its internal cold junction compensation. Additional optional wiring boxes include:
- iNET-510: 0 BNC connectors; supports Thermocouples.
- iNET-511: 8 BNC connectors; includes individual banks of screw terminals for each sensor.
- iNET-512: Supports ¼ and ½ bridge strain gage vRef/2 with individual banks of screw terminals.
The system is a stand-alone USB data acquisition unit requiring no external power supply. Included accessories are the hardware device, USB cable, software on CD, mating Hd44 Female Connector, and Hd44 Cover.
Key Product Differences
The primary distinction between models in this series is electrical isolation:
- iNET-600: Standard configuration where I/O signal ground connects to computer ground. Receives power from the USB bus.
- iNET-601: Features ±36V input bank to USB electrical isolation, providing separation between sensor inputs and the host computer interface.
Digital I/O functionality is consistent across the series, consisting of 4 individual TTL-compatible lines (Ch#25...#28) with a 4 mA sink/source capability. Both models utilize the same plastic enclosure dimensions and Hd44 Female Connector for sensor interfacing.
PDFs & Manuals
