Saltar a la búsqueda Saltar al contenido principal Saltar a la navegación

España 800 900 532 | Fuera de España +34 911 776 121 | Bienvenido a nuestro nuevo sitio web. ¿Encontró algún problema o error? Por favor, infórmelo aquí.

Hemos notado que estás en , por favor visita tu sitio local haciendo clic en el enlace a continuación para ofertas y soporte regionales.

FGR

Cuerda calefactora de fibra de vidrio 900 °F máx. y 120-240 voltios

유리섬유 히터 로프 900 °F 최대 및 120-240 볼트
  • 작동 온도 등급 최대 482°C (900°F)
  • 소형 직경 파이프 및 튜브에 감김
유리섬유 히터 로프 900 °F 최대 및 120-240 볼트 FGR FGR
loading all models
Resumen del Producto
  • 추가 기능 1 도전성 표면에 적합, 수분 증기 또는 화학 물질에 내성 없음
  • 노출 온도, 최대 482 °C
  • 히터 폭 0 in
  • 단열 유리섬유
  • 리드 와이어 출구 방향 반대편
  • 제품 구조 옵션 해당 없음
  • 전력 밀도, 최대 4 W/in²
  • 전력 밀도 사양 참고 4 W/in² (선형)
  • 시리즈 ID FGR
  • 온도조절기 유형 내장되지 않음
  • 와이어 길이 24 in

Supported Applications

The Omega OMEGALUX® FGR Series Fiberglass Heater Rope is designed to apply heat to tubing with diameters as small as 3.2 mm (1/8"). These rope heaters can be wrapped around either conductive or non-conductive surfaces.

Operating Conditions & Performance

The series features a maximum allowable operating temperature of 482°C (900°F). Teflon sleeves at the ends are rated to 500°F. The standard diameter is 5 mm (3/16"). Linear wattage is specified as 4 Watts/inch in the primary data sheet specifications.

Configuration Options

The FGR Series offers configurable lengths and voltage options:

  • Heater Lengths: Available in 0.9, 1.8, 2.4 or 3.0 m (3, 6, 8 or 10').
  • Voltage Options: Standard models operate on 120 Vac or Vdc; 240V is optional.
  • Termination: Each end terminates with a 609 mm (24") long fiberglass-insulated lead wire featuring stripped leads.

The series supports the following model configurations based on length and wattage at 120 Volts: FGR-030: 0.9 m (3'), 125 Watts FGR-060: 1.8 m (6'), 250 Watts FGR-080: 2.4 m (8'), 400 Watts FGR-100: 3.0 m (10'), 500 Watts

Key Product Differences

The series includes specific operational constraints and safety requirements documented in the source materials:

  • These units are not moisture-resistant, do not resist vapor or chemicals, and may not be immersed in liquids.
  • Do not fold, wrap, or overlap the heaters during installation.
  • A method of controlling or limiting exposure temperature (such as variable transformers or digital temperature controllers) must always be used.
  • When heating metal surfaces, proper grounding procedures should be observed for safety precautions.
es-ES
ko_KR
Guardar configuración