Besoin d'aide? Appelez-nous: 1-800-663-4209
CSH5-Series
Chauffage en bande en acier inoxydable avec bornes diagonales
Stainless Steel Strip Heater Diagonal Terminals
Modèles en stock
- Une source de chaleur fiable avec gaine en acier inoxydable sans soudure
- Installations de montage sur surface plane
- Utilisé dans des centaines d'applications de chauffage industrielles et commerciales
- Fours
CSH5-Series
À partir de
C$
214.10
Modèles en stock
Aperçu du produit
- Facteur de forme Bande
- Hauteur 0 in
- Courant, max Raccordement par fil conducteur : 10 amp ; Raccordements par vis : 10-32UNF—25 amp
- Taille de la fente de montage 8 mm x 13 mm
- Nombre de trous de montage 2
- Taille physique Limites de construction Largeur : 16 mm (5/8") Chauffages larges : +0,000, -0,005"; 25 mm et 38 mm (1 et 1 1/2") Chauffages larges : +0,000, -0,010"; Épaisseur : 6 mm (1/4") Chauffages épais : +0,000, –0,005"; 8 et 10 mm (5/16 et 3/8") Chauffages épais : +0,000, –0,008"; [Les chauffages de 10 mm (3/8") d’épaisseur ont des coins arrondis]; Longueur : Jusqu’à 24" : ± 1/16"; Plus de 24" : ± 1/8"
- Densité de puissance, max 45 W/po²
- Tolérance de puissance 5 %, -10 %
- Tolérance de résistance 10 %, -5 %
- ID de série CSH5-Series
- Taille des douilles spéciales 13 mm x 16 mm
- Terminaison Bornes parallèles sur un côté
- Tension maximale 480 Vca
- Remarque sur la tension 480 Vac (lorsque applicable)
Supported Applications
The Omega CSH5 Series consists of ceramic-insulated, flat-surface heating elements with a seamless Type 304 Stainless Steel sheath. These channel strip heaters are designed for industrial and commercial heating applications including ovens, hot plates, dies, molds, drying processes, melting, baking, incubators, platens, food warmers, welding preheating, air heating, sealing bars, thermoforming, and tank heating.
Operating Conditions & Performance
The series features a maximum sheath temperature of 650°C (1200°F). Electrical specifications support a maximum voltage of 480 Vac (dependent on design parameters) with a maximum recommended voltage of 480V when using lead wire terminations. Amperage limits are defined by the termination method: Lead Wire Termination supports up to 10 amp, while Screw Terminations (10-32UNF) support up to 25 amp.
Performance ratings include a nominal watt density of 20 Watts/in² (3.1 Watts/cm²), with a maximum watt density of 45 Watts/in² dependent on design parameters. Tolerances are specified as Resistance: 10%, -5% and Wattage: 5%, -10%. The heaters utilize a rectangular tube construction to maximize heat transfer.
Configuration Options
The CSH5 Series is offered in four standard rectangular sizes with specific availability constraints regarding mounting tabs:
- 16 W x 6 mm thick (5/8" x 1/4"): Available without mounting tabs only.
- 25 W x 8 mm thick (1" x 5/16"): Available with or without mounting tabs. Mounting tabs are not available when supplied with Type L lead wire termination.
- 38 W x 8 mm thick (1 1/2" x 5/16"): Available with or without mounting tabs. Mounting tabs are not available when supplied with Type L lead wire termination.
- 38 W x 10 mm thick (1 1/2" x 3/8"): Available with or without mounting tabs; these heaters feature radius corners. Mounting tabs are not available when supplied with Type L lead wire termination.
Termination options include Screw Terminal Terminations: Type T1 (10-32 Screw Terminals at each end), Type T2 (Tandem at one end), Type T3 (Parallel at one end), and Type T4 (Offset at one end). Lead Wire Terminations are available as Type L (exit from end) or Type L1 (exit from top).
Protection and accessory options include:
- Cable Protection: Type W1 (Wire braid), Type W2 (Stainless steel braid), Type R1 (Armor cable), Type R2 (Right-angle armor cable).
- Terminal Boxes & Plugs: Type P (High-Temperature Quick Disconnect Plug), Type C (Terminal box), Type MP (Specially designed box welded to heater with epoxy potting).
- Ceramic Covers for Insulating Terminals: Igloo™ covers including Type C6 (Double Port In-Line), Type C7 (Double Port 90°), and Type C8 (Single Port) with a Ceramic Cap Thread of 10-32.
Physical construction tolerances vary by dimension: Width for 16 mm heaters is +0.000, -0.005"; width for 25 mm and 38 mm heaters is +0.000, -0.010". Thickness tolerance for 6 mm heaters is +0.000, -0.005", while 8 and 10 mm heaters are +0.000, -0.008". Length tolerances are ±1/16" up to 24" and ±1/8" over 24".
Key Product Differences
Variants within the CSH5 Series differ primarily by cross-sectional dimensions, length (up to or exceeding 24 inches), termination type, and the presence of mounting tabs. Heaters supplied without mounting tabs have ends silver soldered shut to prevent moisture and contaminants from entering. The series does not support exposed electrical wiring as this violates safety codes including O.S.H.A.
PDF & Manuels
Afficher les évaluations et les avis