Need assistance? Call us: 1-800-663-4209
OM-CP-OCTPRO-Logger
8-Channel Programmable Portable Data Logger - Touch Screen
Models In Stock
- Touchscreen interface allows easy configuration without a PC or software
- Measures temperature, current, voltage, and pulse across 8 channels simultaneously
- Compatible with thermocouples, RTDs, thermistors, and voltage-output sensors
- Built-in memory stores data with real-time display and downloadable USB output
OM-CP-OCTPRO-Logger
From
C$
1,768.20
Models In Stock
Product Overview
- AC Power Plug Type N/A
- Accuracy ± 0.1 %
- Accuracy Detail Current Accuracy: ±0.024 mA Voltage Accuracy: ±0.1 mV, ±0.01 V Thermistor Accuracy: ±0.50% RTD Accuracy: ±0.1 °C Thermocouple Accuracy: J, K, T, E, N: ±0.5 °C R, S, B: ±2.0 °C
- Battery Size and Type 3.7V Li-ion
- Calibration Factory calibration is recommended annually
- Data Interface USB
- Dimensions Note 6.65 in x 4.40 in x 1.41 in (168.9 mm x 111.8 mm x 35.8 mm) Data logger only
- Display Note LCD Touchscreen: 5 inch LCD capacitive touchscreen.
- Display Type LCD
- Enclosure Ratings IP20
- Frequency Input Range 0 to 25 kHz
- Height 6.65 in
- Impedance Input Current Input Impedance: 30Ω,Voltage Input Impedance: 1 GΩ,Frequency Input Impedance: 58 kΩ
- Input Control Signal Millivolt input: -100 to 2450 mV Volt input: -0.5 V to 12.0 V
- Input Current -5 to 50 mA
- Input Type Thermocouple, RTD, Thermistor, Current,Voltage, Digital
- Length 1.41 in
- Materials Polycarbonate
- Memory 1,000,000 or 5,000,000 Readings
- Memory Note 1,000,000 or 5,000,000 Readings
- Mounting Handheld, Tabletop or Wall Mounting
- Pulse Input Note 0 to 4,000,000,000 Pulses
- Relative Humidity 0 to 95% RH non-condensing
- Resolution 0.1 °C
- Resolution Note Current Resolution: 0.0001 mA Voltage Resolution: 0.0001 mV, 0.0001 V RTD Resolution: 0.01 °C Thermisor Resolution: 0.01 °C Thermocouple Resolution: J, K, T, E, N: 0.1 °C R, S, B: 0.5 °C
- Sampling Rate 4 kHz
- Series ID OM-CP-OCTPRO-Logger
- Start Modes Delayed Start, Immediate Start
- Supply Power Note • Rechargeable 3.7 V Lithium Ion Battery, • Continuous on-screen sampling: 9 hours; Stand-by mode: 100 hours
- Supply Power Type USB
- Temperature Measurement Range J: -200 to 760 °C,K: -270 to 1370 °C,T: -270 to 400 °C,E: -270 to 980 °C,R: -50 to 1760 °C,S: -50 to 1760 °C,N: -270 to 1300 °C,B: 50 to 1820 °C,RTD: -200 to 850 °C,TH 2252Ω, 10KΩ: -25 to 150°C
- Thermocouple Type J, K, T, E, N, R, B, S
- Weight 1.3 lb
- Width 4.4 in
- Wiring/Connector Table 2-, 4-Wire RTD
The OM-CP-OCTPRO Logger is an all-in-one solution for applications that require immediate analysis. Equipped with eight input channels, the OCTPRO can simultaneously measure current, voltage, temperature and pulse, providing users with real-time data at a moments notice. Theres no need for a PC, users can view all data in tabular or graph form on the 5† touch screen, full-color display.
OM-CP-OCTPRO Logger Highlight Versatility makes OM-CP-OCTPRO the perfect companion for industrial engineers, quality assurance professionals, compliance officers or automotive technicians. The OM-CP-OCTPRO is very easy to use and configure via the built in capacitive touchscreen graphic display.
Applications
- Process Monitoring
- Machine efficiency studies
- Multi-use Laboratory and R&D applications
Setting Up the OM-CP-OCTPRO
I
Channel Configuring the OM-CP-OCTPRO
Applications
- Process Monitoring
- Machine efficiency studies
- Multi-use Laboratory and R&D applications
I
PDFs & Manuals
Software & Drivers
Accessories
accessories
Show Ratings & Reviews
Can we connect strain gauge sensors or SG quarter bridge with this logger. And LVDT with 80mv/v could be connected with this logger?
Thank you for your question. We will require more information to help on this question, please email the DAS team at DAS@dwyeromega.com
Date published: 2025-06-05
The OM-CP-OCTPRO won't turn back on, how can I trouble shoot it? I have tried changing the charging cable. Any suggestions as to why it won't turn back on?
Thank you for your question. We will require more information to help on this question, please email the DAS team at DAS@OMEGA.COM”
Date published: 2021-12-09
What are the power requirements to keep the unit continuously powered? The battery life is far too short for a semi-permanent installation.
Assuming that I don't have a 120 VAC plug in handy inside of the controller where I'd need to install the logger though, I'd need to provide power another way. I assume that it's expecting 5V on the USB circuit, but how much amperage will it draw? I can provide 5V more easily than 120V, but I'd still need to know the load.
Date published: 2022-11-23
What is the sample rate range?
Copied and pasted from the spec page:
All channels will use the same reading rate. Reading rates will be capped at 4 Hz when a temperature channel is selected.
Date published: 2024-11-13
There is one issue that continually comes up, in that it doesn't recognize a USB stick when inserted, so it is difficult to transfer the data off of the unit. Is there a workaround or firmware update available?
Thank you for your question. Please note that the USB drive should not be inserted until the OM-CP-OCTPRO is fully booted. If the USB drive is inserted before the OM-CP-OCTPRO is started, the drive will not be recognized. Please wait until the device is running, and then insert the USB drive. If you have further issues please e-mail DAS Engr-DAS@OMEGA.COM.
Date published: 2022-07-05
Channel 9 details? The manual is not clear on how ch 9 is connected to the system, just says "Port 9 serves as an alarm output". Are there any other details available (voltage, current limits, etc.)? Need to determine what, if anything, can be connected.
Thank you for your question. Please e-mail this request to our Data Acquisition Engr Dept- DAS@OMEGA.COM
Date published: 2023-03-28
How often is calibration recommended? Aside from standards is there a manufacturer time frame for this?
Thank you for your question. With all of our loggers, we recommend calibrating every year. However, this is not any sort of official specification or requirement; this is just our general recommendation. How often a user has the device calibrated will depend on their specific accuracy needs, any regulatory requirements they need to conform to, etc. So, ultimately, how often they calibrate the device will be their decision.
Date published: 2021-03-11
I need a downloadable data sheet for this product. Where can this be found? Thanks!
Hello
Please send request to das@omega.com
Thank you!
Date published: 2020-02-12