1-800-663-4209 | Bienvenue sur notre nouveau site Web, vous avez rencontré un problème ou un bug? Veuillez le signaler ici
DPI-AL-Series
Indicateur de procédé/température avec sorties d'alarme
- Certifié CE, homologué UL
- Entrées universelles
- Haute précision
- 2 sorties d’alarme relais
DPI-AL-Series
À partir de
C$
507.32
Aperçu du produit
- Précision ± 0,5 °C
- Précision ±0,5°C température; 0,03 % lecture
- Fonctions supplémentaires 1 Écran couleur programmable à 3 couleurs
- Modes d'alarme Bande, Élevé/Faible, Verrouillage/Déverrouillage, Normalement ouvert/fermé, Processus/écart
- Sortie de commande Relais SPDT 2
- Plage de mesure du courant 0 à 20 mA
- Type d'affichage Remarque Aucun
- Hauteur 48 mm
- Impédance d'entrée 10 MΩ pour 100 mV, 1 MΩ pour 1 ou 10 Vcc
- Type d'entrée Thermocouple ; RTD ; Courant ; Tension
- Nombre d'entrées 1
- Température de fonctionnement, max 55 °C
- Température de fonctionnement, min 0 °C
- Détails de la sortie Sorties des relais d'alarme 1 et 2 : SPDT, 250 Vac ou 30 Vcc à 3 A (charge résistive)
- Taux de lecture 3 échantillons/sec
- Humidité relative 90 % HR sans condensation
- Type RTD Capteur Pt 100/500/1000 Ω ; 2, 3 ou 4 fils ; α = 0,00385 ou 0,00392
- Fréquence d'échantillonnage 3 Hz (3 mises à jour/seconde)
- Alimentation du capteur/transmetteur 24 Vcc à 25 mA
- ID de série DPI-AL-Series
- Stabilité de la température RTD : 0,04°C/°C ; Thermocouple à 25°C (77°F) : 0,05°C/°C, compensation de la jonction froide ; Processus : 50 ppm/°C ;
- Résistance du fil du thermocouple, max 100 Ω
- Type de thermocouple J ; K ; T ; E ; N ; R ; S ; B ; C ; L
- Plage de mesure de tension 0 à 100 mV ; 0 à 1 V ; 0 à 10 Vcc
*Découvrez notre toute nouvelle gamme de compteurs numériques à panneau avec connectivité Modbus, entrées universelles et programmation PC simple - Série DPPT.*
Les compteurs OMEGA® iSeries avec alarmes offrent une grande flexibilité dans les applications de mesure de processus et d'alarme. Ils acceptent 10 types de thermocouples différents, 18 combinaisons de RTD ou 4 entrées de tension/courant de processus et fournissent 2 sorties d'alarme à relais et un grand écran multicolore programmable. Les options facilement configurables comprennent 11 conditions d'alarme différentes. Les boutons de configuration du panneau avant permettent à l'utilisateur de sélectionner le type d'entrée, les conditions d'alarme et la couleur d'affichage correspondante. Les entrées de processus sont entièrement modulables et prennent en charge pratiquement toutes les unités techniques avec une virgule décimale sélectionnable, offrant ainsi une solution parfaite pour les entrées de pression, de débit ou autres entrées de processus. Les caractéristiques standard comprennent une source d'excitation 24 Vcc intégrée pour les transmetteurs ou autres appareils et une alimentation électrique universelle acceptant 90 à 240 Vca. Une option basse consommation est disponible, prenant en charge 24 Vca ou 12 à 36 Vcc.
PDF & Manuels
Afficher les évaluations et les avis
Rated 4 out of
5
by
bobb from
Good Product
Pleased with the product. Easy to program , preforms well.
Shipping is a little slow, and even though I ordered the product from Omega located in Connecticut, the product shipped from California, and had I known this I would have selected a different shipping method.
Date published: 2016-03-29
Rated 5 out of
5
by
jsulzer from
Cost effective and flexible!
Replaced a unit that was damaged due to lightning strike. First one worked for years until millions of volts decided to destroy it. GREAT tech support when the manual and menu was less than obvious.
Date published: 2016-05-23
As a follow-up to the thread about the LCGB-500 load cell, if the DPiS32 is powering the load cell, which port does the shield cable connect to?
There isn't any provision on the DPiS32 to connect the shield from the load cell. You would need to connect it to an external earth ground.
Date published: 2025-01-21
Is the DPiS32 compatible with the LCGB-500 load cell?
Yes, The DPiS32 is compatible with the LCGB-500 load cell. It will both power and read the output signal directly from the load cell. Please note that the DC powered version of the display (DPiS32-DC) does not have the built-in excitation power to drive the load cell. External excitation power would need to be provided to the load cell if you use a DC powered version of this display.
Date published: 2025-01-18
Is it possible to program the output to display a temperature reading directly correlated to the voltage input? (i.e. 2.175 VDC = 500°F or 4.51 VDC = 1000°F)
Yes, it can be done. If you start with the CNI32 or 16 or 8S, for strain, that unit has 10 point linearization and should be able to. However, we would like to better understand the application to confirm this and advise accurately. Please contact our Tech Support to best advise on the application and product recommendations. Thank you.
Date published: 2021-08-10
Can you provide the ethernet cable wiring diagram?
Hi Jerry,
Thank you for the inquiry. Following linked manual provides wiring details of the ethernet cable.
https://assets.omega.com/manuals/M5023.pdf
Best regards
OMEGA
Date published: 2024-10-27
what does - opn mean on the display?
"OPN" on the display of the I Series panel meters means that the input signal is missing. Check wiring to the input to make certain connections are all there and complete and sensors attached are functioning properly. You can also check the INPUT type selected in the menu to make certain that the setting matches the actual input type being applied.
Date published: 2020-01-21
Is this compatible with LC103B-2K load cells?
The CNi/DPi Series controller/displays are not compatible with strain gage based sensors like the LC103B load cells. The CNiS/DPiS variants of this series are compatible with strain gage based sensors but they will only accept a unipolar input signal so you would not be able to use the load cell to measure in both tension and compression. Suggest you look at Platinum Series Controllers/Displays CN32PT,CN16PT,CN8PT,DP32PT,DP16PT and DP8PT.
Date published: 2024-03-01