Netherlands 07077 03815 | Intl +31 (0) 7077 03815 | Welcome to our new site - found a bug? Please report it here
OM-USB-1608G-Series
16-Channel Voltage Input High Speed USB Data Acquisition Modules
- 16-Bit High-Speed USB Devices
- Acquisition Rates Ranging From 250 kS/s to 500 kS/s
- 8 Differential (DIFF) or 16 Single-Ended (SE) Analog Inputs (Software Selectable)
- Up to 2 Analog Outputs
OM-USB-1608G-Series
From
€
579,07
Product Overview
- A/D Conversion Successive approximation
- Bandwidth 750 kHz
- Calibration Calibration Method: Self-calibration (firmware), Calibration Interval: 1 year (factory calibration), AI Calibration Reference +5V, ±2.5 mV maximum (actual measured values stored in EEPROM)
- CMRR 86 dB
- Configuration Parameters Edge/Level Trigger Mode, Pull-Up/Down Configuration, User-Configurable Input/Output
- Data Interface Ethernet
- Data Interface Note Configuration Method: TracerDAQ Software;Supported Operating System: Microsoft Windows® VISTA/7/8/10 (32-bit and 64-bit)
- Digital Input Digital: Low = –0.5 to 0.8 Vdc
- Digital I/O Note Digital Input/Output Digital Type: CMOS Number of I/O: 8 Configuration: Each bit may be configured as input (power on default) or output Pull-Up Configuration: The port has 47 kΩ resistors configurable as pull-ups or pull-downs (default) via internal jumper (W1) Digital I/O Transfer Rate (System-Paced): 33 to 8000 port reads/writes or single bit reads/writes per second typ, system dependent Input High Voltage: 2.0V minimum, 5.5V absolute maximum Input Low Voltage: 0.8V maximum, -0.5V absolute minimum,0V recommended minimum Output High Voltage: 4.4V minimum (IOH = -50 µA), 3.76V minimum (IOH = -2.5 mA) Output Low Voltage: 0.1V maximum (IOL = 50 µA), 0.44V maximum (IOL = 2.5 mA) Output Current: ±2.5 mA maximum;Cross talk: -75 dB;Transfer Rate: Digital and Counter: 33 to 8000 port reads/writes or single bit reads/writes per second typ, system dependent;Pulse Width: Trigger Pulse Width: 100 ns minimum, Counter: High Pulse Width: 25 ns, minimum, Low Pulse Width: 25 ns, minimum, Clock Pulse Width: AxCKI: 400 ns minimum, AxCKO: 400 ns minimum;Schmitt Trigger Hysteresis: 0.4V to 1.2V
- Digital Output ±2.5 mA maximum
- Frequency Input Range 20 MHz
- Height 35.6 mm
- Impedance Input 1 GΩ (Power on); 820 Ω (Power off)
- Input Bias Current ±10 nA
- Input Capacitance 60 pf
- Input Configuration Connected Software
- Input Type Voltage, Digital
- Input Voltage Note Absolute Maximum Input Voltage: CHx Relative to AGND: ±25V maximum (Power On); ±15V maximum (Power Off)
- LED Indicators Supply Status LED
- Length 127 mm
- Memory Non-Volatile
- Microcontroller Internal Clock Frequency: 64 MHz
- Number of Channels, Input Analog: 8 Differential /16 Single-Ended, Digital: 8, Counter: 2
- Number of Channels, Output Digital: 8
- Operating Temperature, Max 55 °C
- Operating Temperature, Min 0 °C
- Output Settling Time 10V Step: 40 μs
- Output Signal Digital, Clock
- Pull-down Resistor GND
- Pull-up Resistor 47 kΩ
- Relative Humidity 0 to 90% RH non-condensing
- Sampling Rate Note Software Paced: 33 to 4000 S/s, Hardware Paced: 250 kS/s max
- Slew Rate 9 V/μs
- Stability 15 ppm/1000 hours
- Storage Temperature, Max 85 °C
- Storage Temperature, Min -40 °C
- Supply Current 230 mA
- Supply Power Note +5V User Output Voltage Range (Available at Terminal 42): 4.9V minimum to 5.1V maximum +5V User Output Current (Available at Terminal 42): 10 mA maximum
- Supply Voltage 5 Vdc
- Temperature Coefficient 5 ppm/°C
- Timer Output Timer Terminal Name: TMR;Timer Type: PWM output with count, period, delay, and pulsewidth registers;Output Value: Default state is idle low with pulses high, software selectable output invert;Internal Clock Frequency: 64 MHz;Register Widths: 32-bit;High Pulse Width:15.625 ns minimum;Low Pulse Width:15.625 ns minimum;Output High Voltage: 4.4V minimum (IOH = -50 μA), 3.76V minimum (IOH = -2.5 mA);Output Low Voltage: 0.1V maximum (IOL = 50 μA), 0.44V maximum (IOL = 2.5 mA);Output Current: ±2.5 mA maximum
- USB Cable Length 3 m
- Voltage Measurement Range ±10V, ±5V, ±2V, ±1V
- Warm Up Time 15 min
- Weight 160 g
- Width 89.9 mm
The OM-USB-1608G Series devices are low-cost, high-speed, analog and digital I/O USB devices. All of these devices offer up to eight differential (DIFF) or 16 single-ended (SE) analog inputs, up to eight digital I/O channels, two counter inputs, and one timer output. The OM-USB-1608GX-2AO offers two, 16-bit analog output channels with DAC rates up to 500 kS/s. Everything you need to begin acquiring, viewing, and storing data is included with each OM-USB-1608G Series device, including comprehensive software support.
Analog Input
OM-USB-1608G Series devices provide 16-bit analog inputs that are software-selectable as 16 SE or eight DIFF inputs. These devices also support input ranges of ± 10V, ± 5V, ± 2V, and ± 1V that are software-selectable per channel
Analog Output
(OM-USB-1608GX-2AO only) The OM-USB-1608GX-2AO has two 16-bit analog outputs. Both outputs can be updated at a rate of 250 kS/s per channel; one output can be updated at a rate of 500 kS/s. The output range is fixed at ± 10V. The outputs default to 0 V when the host PC is shut down or suspended, or when a reset command is issued to the device.
Trigger Input
OM-USB-1608G Series devices have an external digital trigger input. The trigger mode is software-selectable for edge- or level sensitive mode. You can configure edge-sensitive mode for either rising or falling edge. In level sensitive mode, you can configure for either high or low level. The default setting at power up is edge-sensitive, rising edge.
Re-trigger Mode:
In re-trigger mode, you can set up repetitive analog input trigger events. The trigger is automatically re-armed after it is activated. Use software to set the A/D trigger count (the number of samples you want per trigger).
Digital I/O
Eight bidirectional digital I/O connections are included with OM-USB-1608G Series devices. Each digital channel is individually configurable for input or output. The digital I/O terminals can detect the state of any TTL-level input. You can configure for pull-up (+ 5V) or pulldown (0V) through a jumper.
Counter Input
Each OM-USB-1608G Series device includes two 32-bit event counters for counting TTL pulses. The counters accept frequency inputs of up to 20 MHz.
Timer Output
OM-USB-1608G Series devices have a PWM timer output that can generate a pulse output with a programmable frequency in the range of 0.0149 Hz to 32 MHz. The timer output parameters are software-selectable.
External Clock I/O
OM-USB-1608G Series devices provide one external clock input and one external clock output for the analog inputs. The OM-USB-1608GX-2AO also has one external clock input and one external clock output for the analog outputs.
Software
The OM-USB-1608G modules ship with an impressive array of software, including the new TracerDAQ®, a fullfeatured, out-of-the-box data logging, viewing, and analysis application. Driver support and detailed example programs are included for Universal Library programming libraries for Microsoft® Visual Studio® programming languages, and other languages, including DASYLab®, and ULx for NI LabVIEW® (comprehensive library of VIs and example programs compatible with 32-bit and 64-bit LabVIEW v8.5 through 2012) and InstaCalTM installation, calibration and test utility-powerful solutions for programmers and nonprogrammers alike. These modules operate under Microsoft Windows® XP (32-bit only) and VISTA/7/8 (32-bit and 64-bit) operating systems.
The OM-USB-1608G data acquisition modules are supplied with TracerDAQ software which is a collection of four virtual instrument applications used to graphically display and store input data and generate output signals:
• Strip Chart—Log and graph values acquire from analog inputs, digital inputs, temperature inputs and counter inputs
• Oscilloscope—Display values acquired from analog inputs
• Function Generator—Generate waveforms for analog outputs
• Rate Generator—Generate waveforms for counter outputs
TracerDAQ PRO is an enhanced version of TracerDAQ and is available as a purchased upgrade
(SWD-TRACERDAQ-PRO). A comparison of some of the features included in TracerDAQ vs TracerDAQ PRO is shown on the PDF.
Analog Input
OM-USB-1608G Series devices provide 16-bit analog inputs that are software-selectable as 16 SE or eight DIFF inputs. These devices also support input ranges of ± 10V, ± 5V, ± 2V, and ± 1V that are software-selectable per channel
Analog Output
(OM-USB-1608GX-2AO only) The OM-USB-1608GX-2AO has two 16-bit analog outputs. Both outputs can be updated at a rate of 250 kS/s per channel; one output can be updated at a rate of 500 kS/s. The output range is fixed at ± 10V. The outputs default to 0 V when the host PC is shut down or suspended, or when a reset command is issued to the device.
Trigger Input
OM-USB-1608G Series devices have an external digital trigger input. The trigger mode is software-selectable for edge- or level sensitive mode. You can configure edge-sensitive mode for either rising or falling edge. In level sensitive mode, you can configure for either high or low level. The default setting at power up is edge-sensitive, rising edge.
Re-trigger Mode:
In re-trigger mode, you can set up repetitive analog input trigger events. The trigger is automatically re-armed after it is activated. Use software to set the A/D trigger count (the number of samples you want per trigger).
Digital I/O
Eight bidirectional digital I/O connections are included with OM-USB-1608G Series devices. Each digital channel is individually configurable for input or output. The digital I/O terminals can detect the state of any TTL-level input. You can configure for pull-up (+ 5V) or pulldown (0V) through a jumper.
Counter Input
Each OM-USB-1608G Series device includes two 32-bit event counters for counting TTL pulses. The counters accept frequency inputs of up to 20 MHz.
Timer Output
OM-USB-1608G Series devices have a PWM timer output that can generate a pulse output with a programmable frequency in the range of 0.0149 Hz to 32 MHz. The timer output parameters are software-selectable.
External Clock I/O
OM-USB-1608G Series devices provide one external clock input and one external clock output for the analog inputs. The OM-USB-1608GX-2AO also has one external clock input and one external clock output for the analog outputs.
Software
The OM-USB-1608G modules ship with an impressive array of software, including the new TracerDAQ®, a fullfeatured, out-of-the-box data logging, viewing, and analysis application. Driver support and detailed example programs are included for Universal Library programming libraries for Microsoft® Visual Studio® programming languages, and other languages, including DASYLab®, and ULx for NI LabVIEW® (comprehensive library of VIs and example programs compatible with 32-bit and 64-bit LabVIEW v8.5 through 2012) and InstaCalTM installation, calibration and test utility-powerful solutions for programmers and nonprogrammers alike. These modules operate under Microsoft Windows® XP (32-bit only) and VISTA/7/8 (32-bit and 64-bit) operating systems.
The OM-USB-1608G data acquisition modules are supplied with TracerDAQ software which is a collection of four virtual instrument applications used to graphically display and store input data and generate output signals:
• Strip Chart—Log and graph values acquire from analog inputs, digital inputs, temperature inputs and counter inputs
• Oscilloscope—Display values acquired from analog inputs
• Function Generator—Generate waveforms for analog outputs
• Rate Generator—Generate waveforms for counter outputs
TracerDAQ PRO is an enhanced version of TracerDAQ and is available as a purchased upgrade
(SWD-TRACERDAQ-PRO). A comparison of some of the features included in TracerDAQ vs TracerDAQ PRO is shown on the PDF.
PDFs & Manuals
Software & Drivers
