한국 1588-8983 | 새로운 웹사이트에 오신 것을 환영합니다. 문제나 버그를 발견하셨나요? 여기에 보고해주세요
CN38S-Series
민감 터치 키패드가 장착된 온도 자동 조정 컨트롤러
温度オートチューンコントローラ(感度の高いタッチキーパッド付き)
재고가 있는 모델
- 설치가 간편한(툴리스 가능) 프로그래밍
- 열전대, RTD 및 서미스터 입력
- 자동 스케일 변경(오토 레인징) 기능이 있는 0.1°C 해상도
- “감도 높은 터치” 키패드
제품 개요
- 정확도 ± 0.5%
- 정확도 세부 사항 ± (0.5% 스팬 ± 1 디지트 @25 °C)
- 추가 기능 1 °C 또는 °F 프로그래밍 가능
- 과전압 카테고리 II
- DC 펄스 절연: 매우 저전압 부품에 관해서는 출력이 절연되지 않음; 논리 상태: 1: 12 V ± 20% @ 1 mA, 10 V ± 20%; @ 20 mA; 논리 상태 0: <0.5 V
- 장치 클래스 클래스 II
- 디스플레이 크기 47 mm (1.9인치)
- 디스플레이 유형 3자리 LED
- 디스플레이 유형 노트 3자리 단일 표시, 적색, 12 mm (0.47")
- 디스플레이 갱신 시간 1 s
- 전기 연결 나사 단자
- 외함 등급 IP65
- 인클로저 등급 노트 전면 보호: 실내 사용용 EN60070-1에 따른 IP 65(가스켓 포함) 스크류 터미널: IP20
- 폼팩터 1/8 DIN
- 높이 78 mm
- 고립 저전압(입력 및 출력 릴레이)과 전면부 사이의 강화된 절연; 저전압과 극저전압 부품(입력, 정적 출력) 사이의 강화된 절연
- 길이 64 mm
- 측정 유형 온도
- 장착 패널 내 플러시
- 명목 펄스 전압 2.5 KV
- 제어 출력 수 2
- 입력 수 1
- 작동 온도, 최대 50 °C
- 최소 작동 온도 0 °C
- 상대 습도 응축 없이 < 95 RH%
- 샘플링 속도 1 Hz (1초 업데이트 1회)
- 시리즈 ID CN38S-Series
- 저장 온도, 최대 60 °C
- 보관 온도 최소 -25 °C
- 무게 180 g
- 폭 35 mm
Supported Applications
The Omega CN38S Series is a microprocessor-based digital electronic controller designed for temperature measurement and control applications. The series features an ergonomic keypad with 'Sensitive Touch' technology intended to provide protection against dust and liquids while allowing direct set-point access. It supports ON/OFF or PID control modes, including autotuning functionality.
Documented sensor compatibility includes:
- Thermocouples: Type J and K
- RTDs: Pt 100 and Pt 1000 (2-wire)
- Thermistors: PTC (990 Ω @ 25°C) and NTC (10 kΩ @ 25°C)
The instrument is intended for indoor use in an electrical panel with exposed terminals. It is not designed for hazardous locations, nor should it be used as safety equipment or in applications where failure may cause dangerous situations.
Operating Conditions & Performance
The CN38S Series operates within a specified ambient temperature range of 0 to 50°C (32 to 122°F) and supports humidity levels up to <95 RH% without condensation. The front panel offers IP65 protection with an optional gasket according to EN60070-1, while the screw terminal block is rated IP20.
Performance specifications vary by input type:
- Accuracy: ±(0.5% span ±1 digit) @ 25°C
- Resolution: 0.1°C with automatic scale change (autorangeing)
- Response Time: Sampling rate of 1 s; display updating time of 1 s
- Storage Temperature: -25 to 60°C (-13 to 140°F)
The controller features a 3-digit red display and includes programmable parameters for set points, alarms, soft start time, compressor protection time, and password-protected configuration.
Measurement Ranges by Sensor Type
- Type J/K Thermocouple: -40 to 999°C (-40 to 999°F)
- RTD (Pt 100, Pt 1000): -50 to 850°C (-58 to 999°F) and -50.0 to 99.9°C (-58.0 to 99.9°F)
- PTC Thermistor: -50 to 150°C (-67 to 302°F) and -50.0 to 99.9°C (-67.0 to 99.9°F)
- NTC Thermistor: -50 to 110°C (-58 to 230°F) and -50.0 to 99.9°C (-58.0 to 99.9°F)
Configuration Options
The CN38S Series is configurable across input types, output signals, and power supply options. The model number follows the format: CN38S-<INPUT_TYPE>-<OUTPUT1>-<OUTPUT2>-<VOLTAGE>.
Input Types
- TC: Thermocouple Type J or K
- RTD: Resistance Temperature Detector (Pt 100, Pt 1000)
- TH: Thermistor (PTC or NTC)
Output Configurations
The series supports two independent outputs with the following options:- R1 / R2: SPDT Relay, 8 A/250 Vac on resistive load (6A AC3/250 VAC), or 3 A/250V
- DC1 / DC2: DC pulse for SSR drive. Not isolated; specifications include 12V ±20% @ 1 mA, 10V ±20% @ 20 mA, and OFF state <0.5V.
Output functions are programmable via parameters to support PID control (heating or cooling action), ON/OFF control, absolute high/low alarms, band alarms, deviation alarms, and second set-point control.
Power Supply Options
The series is available with the following power inputs:- (None): 100 to 240 VAC/VDC (±10%) or 100 to 230 Vac/Vdc (±10% depending on source)
- 12V: 12 VDC isolated (-15% to +10%)
- 24V: 24 VAC/DC (-15% to +10%) or 24 Vac/Vdc (±10%)
Mechanical & Electrical Connections
- Dimensions: Front panel cutout approximately 78 x 35 mm; overall depth varies by housing configuration.
- Mounting: Panel mounting with a maximum thickness of 15 mm. Housing material is plastic, self-extinguishing (V-0 according to UL 94).
- Connections: 11 screw terminals (M3) for cables from 0.25 to 2.6 mm² (AWG 22 to AWG 14).
Key Product Differences
The CN38S Series distinguishes itself through specific input/output combinations and voltage ratings rather than distinct sub-series names.- Input Distinction: Models are designated by -TC-, -RTD-, or -TH- to define the sensor family supported.
- Output Pairing: Variants combine relay outputs (R1, R2) and DC pulse outputs (DC1, DC2). Common configurations include Relay/Relay (R1-R2), Pulse/Pulse (DC1-DC2), or mixed DC1-R2.
- Voltage Suffixes: Standard models operate on 100–240 VAC/VDC. Low-voltage variants are explicitly marked with a suffix of -12V (for 12 VDC isolated) or -24V (for 24 VAC/DC).
- Accessories: A field-installable noise suppression kit, model CNQUENCHARC, is available for 110 to 230 Vac applications.
PDF 및 매뉴얼