1-800-663-4209 | Bienvenue sur notre nouveau site Web, vous avez rencontré un problème ou un bug? Veuillez le signaler ici
CN38S-RTD-R1-R2
Temperature Controller with Sensitive Touch Keypad
Choisir une variante
Sortie de commande
Tension d'alimentation
Type d'entrée
Ajouté à votre panier
Configuration complète.
Veuillez ajouter au panier pour la conserver ou quitter la configuration
Veuillez ajouter au panier pour la conserver ou quitter la configuration
Échec de l'enregistrement des configurations, cliquez sur le bouton Configurer pour recommencer
Spécifications du produit
<< Voir tous les modèles de produit| Marque |
 |
| Brûlure | At the end of scale |
| Caractéristiques nominales du boîtier | IP65 |
| Catégorie de surtension | II |
| Classe de dispositif | Class II |
| Connexion électrique | Screw Terminal |
| Détails de la sortie | Relay/Relay;Output Action : Direct/reverse, programmable Contact : SPDT Contact Load : Out 1 - 8 A/250 Vac on resistive load - 3 A/250V Relay Electric Life : 100,000 operations |
| Facteur de forme | 1/8 DIN |
| Fonctions supplémentaires 1 | °C or °F programmable |
| Fréquence d'échantillonnage | 1 Hz (1 update/second) |
| Hauteur | 78 mm |
| Humidité relative | < 95 RH% without condensation |
| ID de série | CN38S-Series |
| Impulsion CC | Isolation: Output NOT isolated as regard the very low voltage parts; Logic State: 1: 12V ± 20% @ 1 mA, 10V ± 20%; @ 20 mA ; Logic State 0: <0.5V |
| Isolation | Reinforced isolation between low voltage (input and output relay) and frontal parts; reinforced isolation between low voltage and very low voltage parts (inputs, static outputs) |
| Largeur | 35 mm |
| Longueur | 64 mm |
| Montage | Flush in panel |
| Nombre d'entrées | 1 |
| Nombre de sorties de commande | 2 |
| Plage de mesure | -50 to 850 (-58 to 999°F) -50.0 to 99.9 (-58.0 to 99.9°F) |
| Poids | 180 g |
| Précision | ± (0.5% span ± 1 digit @25 °C |
| Remarque concernant les indices de protection des boîtiers | Front Protection: IP 65 (with gasket) according to EN60070-1 for indoor use Screw Terminal: IP20 |
| Résistance de la thermistance | None |
| Résolution | 0.1°C |
| Signal de sortie | None |
| Sortie de commande | Relais SPDT 2 |
| Taille d'affichage | 47 mm (1.9 in) |
| Temps de mise à jour de l'affichage | 1 s |
| Température de fonctionnement, max | 50 °C |
| Température de fonctionnement, min | 0 °C |
| Température de stockage, max | 60 °C |
| Température de stockage, min | -25 °C |
| Tension d'alimentation | 100 à 240 Vca/Vcc |
| Tension d'impulsion nominale | 2.5 KV |
| Type d'affichage | 3 Digit LED |
| Type d'affichage Remarque | 3-digit single display, red, 12 mm (0.47") |
| Type d'approvisionnement électrique | AC |
| Type d'entrée | RTD |
| Type de mesure | Temperature |
| Valeur brute du poids | 0.34 |
| Pays d'origine | Italy |
| Voir toutes les spécifications | |
PDF & Manuels
Afficher les évaluations et les avis
Rated 5 out of
5
by
biff from
It's the Bomb!
This little unit works sweet. If you need a 12 volt controller, this is the bomb! I am using this as a fan control for my rocket stove. I needed a higher sensor range than I could get with the 15 dollar Inkbird controller. I haven't had much experience with controllers other than an Inkbird 120v that I used for an old coffee vending machine @ 95c max, and Omega CN7500 120v that I used for a kiln. It seems easy enough to operate. NOTE, the sensor must be isolated. I blew up the first two (my fault) by not isolating the probe from the metal frame of the rocket stove.
Date published: 2017-10-03
Rated 3 out of
5
by
Nickname already used from
Misleading!
The specification sheet shows the unit supporting both Pt100 and Pt1000 sensors, so I ordered the RTD unit only to discover that it supports ONLY Pt100. For Pt1000 support you need to buy the thermistor unit!! The product selection tool and the specifications page make no mention of this - this detail is buried in the manual.
Date published: 2022-05-02
Rated 3 out of
5
by
Lonuf from
Works as needed. Should have more features.
Disappointed in the missing options. Manual shows options that are not available on device. The option to enable decimal point is not installed. Does not make sense as it is a basic function. The menu skips over that option. They do not tell you this and do not give you the model that allows this function.
Date published: 2021-12-22