Besoin d'aide? Appelez-nous: 1-800-663-4209
FTB601B
Tous les capteurs de débit en plastique pour débits faibles à moyens
Ajouté à votre panier
Configuration complète.
Veuillez ajouter au panier pour la conserver ou quitter la configuration
Veuillez ajouter au panier pour la conserver ou quitter la configuration
Échec de l'enregistrement des configurations, cliquez sur le bouton Configurer pour recommencer
Spécifications du produit
<< Voir tous les modèles de produit| Marque |
 |
| Courant d'approvisionnement | 6 à 33 mA |
| Débit volumétrique, max | 2 l/min |
| Débit volumétrique, min | 0.1 l/min |
| Facteur K | 36 000 impulsions/gal |
| Homologations | RoHS, CE |
| ID de série | FTB600-Series |
| Longueur | 3.8 in |
| Longueur du câble | 0.9 m |
| Longueur du filetage | 0.35 in |
| Pression de Fonctionnement Remarque | 150 psig à 79°C (175°F) |
| Pression de Fonctionnement, max | 150 psi |
| Précision | ± 1 % |
| Puissance électrique | Impulsion carrée |
| Répétabilité | ±0,1 % |
| Taille du raccordement au process | 1/4 po |
| Taille du tuyau, max | 0.27 in |
| Tension d'alimentation | 8 à 24 Vcc |
| Type de raccordement au process | Raccord cannelé |
| URL QR de la fiche technique | https://www.dwyeromega.com/en-us/plastic-flow-meters-for-low-to-medium-flow-with-pulse-output/FTB600-Series/p/FTB601B?guid=701a700000ulrduaaq&utm_source=spec-sheet&utm_medium=qr-code&utm_campaign=prd-sku-spec-sheet&utm_content=auto-generated-sku-level-spec-sheet |
| Valeur brute du poids | 0.13 |
| Échelle de viscosité | 1 à 15 cSt |
| Pays d'origine | Netherlands |
| Voir toutes les spécifications | |
PDF & Manuels
Afficher les évaluations et les avis
Rated 1 out of
5
by
Bruce from
Omega FTB600B Faulty Labelling Added Cost
I installed this unit according to the proper direction of flow indicated on the label. Along with the integration of the Omega DPF701 display, I spent many hours trying to get the assembly to indicate the proper flow rate. I finally realized that the direction-of-flow label may be affixed incorrectly. I checked the picture in the manual and, sure enough, the label was upside-down. I reversed the flow and the assembly functioned properly. For $600, I expect a better quality product that does not cost me valuable time to implement. Photo attached.
Date published: 2017-04-07
Rated 5 out of
5
by
erosion researcher from
Compact, easy to install and set up
This sensor is relatively small. After calling tech support for some assistance, it was easy to correctly connect it with the meter. The meter was simple and quick to configure, too.
Date published: 2016-03-09
Rated 5 out of
5
by
Kosanovic from
Good flowmeter for lower temperatures
The flowmeters are easy to setup and use. You need a pulse counter card, alternative is a pulse to voltage converter, for example IFMA0035.
Date published: 2022-02-24
Rated 1 out of
5
by
shoukasg from
Don't operate at the upper temperature limit.
I have burnt out 2 of these flowmeters in a non-corrosive, hot water application. These flow meters are accurate out of the box and have good turndown ratio but I am operating them just under their spec at 180F. The manufacturer claims 185F as the upper limit. I would expect a little wiggle room but I have gone through 2 devices already.
Date published: 2021-05-19