Besoin d'aide? Appelez-nous: 1-800-663-4209
STM17Q-3AE
Integrated Stepper Drives/Motors with Advanced Features and Control Options
Choisir une variante
Type de construction
Interface de données
Ajouté à votre panier
Configuration complète.
Veuillez ajouter au panier pour la conserver ou quitter la configuration
Veuillez ajouter au panier pour la conserver ou quitter la configuration
Échec de l'enregistrement des configurations, cliquez sur le bouton Configurer pour recommencer
Spécifications du produit
<< Voir tous les modèles de produit| Marque |
 |
| Approvisionnement Remarque | External 12 to 70 Vdc power supply required |
| Couple de maintien | 85 oz-po |
| Détails de la sortie | Optically isolated, 24V, 40 mA max NPN/sinking |
| Facteur de forme | NEMA 17 |
| Facteur de forme mécanique et capacité de charge | Rotor Inertia: 0.0037 oz-inch² |
| Fonctions | Fault, motion, tach or general purpose programmable |
| Fonctions supplémentaires 1 | Integrated Driver, Stand Alone Programming |
| Humidité relative | 90 % non-condensing |
| ID de série | SMT-Srs-Stepper-Motors |
| Interface de données | RS232 |
| Interfaces de commande et modes de fonctionnement | Analog Input Voltage: 0 to 5 Vdc; Analog Input Resolution: 12 bits; Current Control: 4 state PWM at 20 kHz; Step and Direction Inputs: STEP ±: Optically isolated, 5 to 24V; minimum pulse width : 250 ns; maximum pulse frequency : 3 MHz; function: step, CW step, A quadrature, encoder following, CW limit, CW jog, start/stop (oscillator mode), general purpose input DIR ±: Optically isolated, 5 to 24V; minimum pulse width : 250 ns; maximum pulse frequency : 3 MHz; function: DIR, CCW step, B quadrature, encoder following, CCW limit, CCW jog, sensor, DIR (oscillator mode), general purpose input; Enable Inputs: EN ±: Optically isolated, 5 to 24V; minimum pulse width : 250 ns; maximum pulse frequency : 3 MHz; function: enable, reset, speed 1/speed 2 (oscillator mode), general purpose input Adjustable bandwidth digital noise rejection filter on all inputs |
| Mode de contrôle | Aucune |
| Protection | Over-voltage, undervoltage, over-temp, motor/wiring shorts (phase-to-phase, phase-to-ground) |
| Précision et fluidité du mouvement | Microstep Resolution: Software selectable from 200 to 51200 steps/rev in increments of 2 steps/rev; Anti-Resonance: Raises the system damping ratio to eliminate midrange instability and allow stable operation throughout the speed range and improves settling time; Torque Ripple Smoothing: Allows for fine adjustment of phase current waveform harmonic content to reduce low-speed torque ripple in the range 0.25 to 1.5 rps; Microstep Emulation: Performs high resolution stepping by synthesizing fine microsteps from coarse steps (step and direction mode only); Command Signal Smoothing: Software configurable filtering reduces jerk and excitation of extraneous system resonances (step and direction mode only) |
| Réglage intelligent et diagnostics | Auto Set-Up: Measures motor parameters and configures motor current control and anti-resonance gain settings; Self Test: Checks internal and external power supply voltages; diagnoses open motor phases and motor resistance changes >40%; detects encoder wiring and signal faults (differential encoder only); Non-Volatile Storage: Programs, data and drive configuration are saved in FLASH and EEPROM memory; Idle Current Reduction: Reduction range of 0 to 90% of running current after delay selectable in milliseconds |
| Température de fonctionnement, max | 50 °C |
| Température de fonctionnement, min | -20 °C |
| Température de service Remarque | 0 to 40°C (32 to 104°F) (mounted to suitable heatsink) |
| Température maximale du processus | 40 °C |
| Température minimale du processus | 0 °C |
| Tension d'alimentation | 12 to 70Vdc |
| Type d'amplificateur | Dual H-Bridge, 4 Quadrant |
| Type de construction | Codeur intégré |
| Valeur brute du poids | 1.6 |
| Pays d'origine | China |
| Voir toutes les spécifications | |
Afficher les évaluations et les avis