1-800-663-4209 | Bienvenue sur notre nouveau site Web, vous avez rencontré un problème ou un bug? Veuillez le signaler ici
DRSL-TC-Srs-Sig-Cond
DIN Rail Thermocouple Input Signal Conditioners | Low Profile
Modèles en stock
- DRSL-TC Non-Isolated and DRSL-TC-ISO Isolated Models
- Accepts Type J and Type K Thermocouples
- Pre-Calibrated Temperature Ranges Selectable via Dip-Switches
- Slimline Housing—Only 6 mm (0.24') Wide
DRSL-TC-Srs-Sig-Cond
Depuis
C$
240.33
Modèles en stock
L'aperçu du produit
- Approvals CE, UL, RoHS
- Calibration Temperature, Max 28 °C
- Calibration Temperature, Min 20 °C
- Electrical Output 4 to 20 mA
- EMC Immunity Note NAMUR NE 21, A Criterion, Burst: <±1% of span (span = selected input range)
- EMC Standard NAMUR NE 21
- Enclosure Ratings IP20
- Height 113 mm
- Installation Pollution degree 2 and measurement/overvoltage category II
- LED Indicators Green LED indicates operational status of the unit and input sensor
- Length 115 mm
- Load Resistance Voltage Output :>10 kΩ min,;Current Output: 21 mA/600 Ω /12.6V max
- Mounting DIN Rail 35 mm Standard, EN 60715
- Operating Temperature, Max 70 °C
- Operating Temperature, Min -25 °C
- Output Value Process
- Power Consumption 0.7 W, Internal - 0.65 W
- Relative Humidity 0 to 95% RH (non-condensing)
- Screw Terminal Torque 0.5 Nm
- Stability Load Stability: ≤0.01% of span/100 Ω
- Storage Temperature, Max 85 °C
- Storage Temperature, Min -40 °C
- Supply Power Type DC
- Weight 70 g
- Width 6.1 mm
- Wire Gauge 26 to 12 AWG
The DRSL-TC Series thermocouple input DIN rail signal conditioners provide a competitive choice in terms of both price and technology for interfacing thermocouple inputs to SCADA systems or PLC equipment.
The DRSL-TC and DRSL-TC-ISO can be used for signal conversion of standard Type J or K thermocouple inputs into unipolar analog signals.
The DRSL-TC-ISO isolated model offers 3-way isolation between input, output and supply and provides surge suppression and protects control systems from transients and noise. Low power consumption facilitates DIN rail mounting without the need for any air gap. Easy configuration of more than 1000 factory calibrated measurement ranges is done via DIP-switches. The unit operates over a wide temperature range from -25 to 70°C (-13 to 158°F).
The DRSL-TC and DRSL-TC-ISO can be used for signal conversion of standard Type J or K thermocouple inputs into unipolar analog signals.
The DRSL-TC-ISO isolated model offers 3-way isolation between input, output and supply and provides surge suppression and protects control systems from transients and noise. Low power consumption facilitates DIN rail mounting without the need for any air gap. Easy configuration of more than 1000 factory calibrated measurement ranges is done via DIP-switches. The unit operates over a wide temperature range from -25 to 70°C (-13 to 158°F).
PDF et manuels
Accessories
installation hardware
Module stop (screwed onto DIN rail to support and hold mounted devices)
C$14.81
35 In Stock
Power rail (with cover and two end covers, one right hand and one le ft hand), 1 m (3.3 ft) length
C$301.98
4 In Stock
meters/controllers
Afficher les notes et les avis
Rated 5 out of
5
by
Anonymous from
Good product, easy to use.
Works great and easy to setup. I didn't use it on a DIN rail but it works fine standalone. The packaging is well done so you can just lay it on a bench or something and it works fine. I'd definitely buy it again anytime I need to log high rate thermocouple data.
Date published: 2024-10-27
Rated 5 out of
5
by
WillPVI from
Clean simple Thermocuple signal conditioner
Very flexible and easy to use. I bought both the isolated and non isolated versions. Small DIN rail footprint. Clear instructions. Just what I needed for a simple data acq project that needed a single thermocouple input.
Date published: 2023-12-31
Why is the drsl-temp option not showing up in the all models section?
DRSL-TEMP is a different series meant for thermocouples and RTD's, it will come up when you look for it on our search engine.
Date published: 2022-11-04