1-800-663-4209 | Bienvenue sur notre nouveau site Web, vous avez rencontré un problème ou un bug? Veuillez le signaler ici
DRSL-SP3-Rptr-Spltr-BP
DIN Rail Isolated Repeater/Splitter for Bipolar Process Signals
Modèles en stock
- Isolation and Conversion of Bipolar Process Voltage and Current Signals to Unipolar/Bipolar Signals
- Splitter Function: 1 Process Input, 2 Process Outputs
- Slimline Housing—Only 6 mm (0.24') Wide
- Multiple Signal Ranges (DIP-Switch Selectable)
DRSL-SP3-Rptr-Spltr-BP
Depuis
C$
474.29
Modèles en stock
L'aperçu du produit
- Approvals CE, UL, RoHS
- Bandwidth 100 Hz or 10 Hz (selectable via DIP-switch)
- Calibration Temperature, Max 28 °C
- Calibration Temperature, Min 20 °C
- Electrical Output 0 to 23 mA
- EMC Immunity Note Extended EMC Immunity NAMUR NE 21, A Criterion, Burst: <±1% of span
- EMC Standard NAMUR NE 21
- Enclosure Ratings IP20
- Height 113 mm
- Installation Pollution degree 2 and measurement/overvoltage category II
- Isolation Isolation: Input/output 1/output 2/supply;Isolation Voltage (Test): 2.5 kVac;Isolation Voltage (Working):300 Vac
- Length 115 mm
- Mounting DIN Rail 35 mm Standard, EN 60715
- MTBF 187 yrs
- Noise Calibration >60 dB
- Operating Temperature, Max 70 °C
- Operating Temperature, Min -25 °C
- Output Value Splitter
- Power Consumption 0.8 W, Internal - max 0.65 W
- Relative Humidity 0 to 95% RH (non-condensing)
- Screw Terminal Torque 0.5 Nm
- Span, Max Corresponds to the presently selected DIP switch output range
- Stability Load Stability: ≤0.002% of span/100 Ω
- Storage Temperature, Max 85 °C
- Storage Temperature, Min -40 °C
- Supply Power Type DC
- Voltage Loss <1 V
- Weight 70 g
- Width 6.1 mm
- Wire Gauge 26 to 12 AWG
The DRSL-SP3 bipolar isolated signal conditioner/splitter provides a competitive choice in terms of both price and technology for galvanic isolation of process voltage or current signals to SCADA systems or PLC equipment. Two process outputs are provided which mirror the single process input.
The DRSL-SP3 can be used for signal conversion of standard bipolar analog process signals into two individual unipolar or bipolar analog signals. The unit offers 4-port isolation, provides surge suppression and protects control systems from transients and noise. The DRSL-SP3 also eliminates ground loops and can be used for measuring floating signals. Low power consumption facilitates DIN rail mounting without the need for any air gap. Factory calibrated measurement ranges are easily configured via DIP switches. The unit operates over a wide temperature range from -25 to 70°C (-13 to 158°F).
The DRSL-SP3 can be used for signal conversion of standard bipolar analog process signals into two individual unipolar or bipolar analog signals. The unit offers 4-port isolation, provides surge suppression and protects control systems from transients and noise. The DRSL-SP3 also eliminates ground loops and can be used for measuring floating signals. Low power consumption facilitates DIN rail mounting without the need for any air gap. Factory calibrated measurement ranges are easily configured via DIP switches. The unit operates over a wide temperature range from -25 to 70°C (-13 to 158°F).
PDF et manuels
Accessories
installation hardware
Module stop (screwed onto DIN rail to support and hold mounted devices)
C$14.81
35 In Stock
Power rail (with cover and two end covers, one right hand and one le ft hand), 1 m (3.3 ft) length
C$301.98
4 In Stock
meters/controllers
Afficher les notes et les avis
Can this be mounted on a normal din rail?
Thank you for your inquiry. Yes, this signal conditioner can be mounted on any standard 35 mm Din Rail.
Date published: 2022-11-17