IN-UVI-Bridge-Amplifier

Wheatstone Bridge In-Line Amplifier w/ Field Selectable I/O

3.0

(2)

Models In Stock

Wide Range of Field Selectable Inputs and Outputs
Ready-Made Cable Assemblies for Transducer Connection Now Available!
Input/Output Isolation
Low Thermal Drift

See Product Overview

IN-UVI-Bridge-Amplifier

From ^$ 2,436.14

Models In Stock

Shop Models

1 Variations available

See all series options below

Data Sheet

Product Overview

Approvals CE
Bridge Resistance 350 to 5000 Ω
Calibration Note Field Installed Shunt Calibration resistor with remote activation for bridge calibration
Capacitance 0.022 µF
EMC <0.15% of FS per EN61326-1 (industrial)
Enclosure Ratings IP65
Height 34.8 mm
Input Noise 10 mV peak to peak @ 3 mV/V voltage mode (10 Vdc) 20 uA peak to peak current mode
Input Range 90 mA, 0.5 mV/V to 4 mV/V in 0.5 steps
Input Range Note Current: 90 mA maximum (must be capable of supplying 200 mA), Sensor Input: 0.5 mV/V to 4 mV/V in 0.5 steps
Input Type Current, Signal
Isolation 100 MΩ @ 500 Vdc
Length 134.8 mm
Linearity 0.0001
Load Resistance 700 Ω at 20 mA
Long Term Stability 0.1% of FS/year
Operating Temperature, Max 60 °C
Operating Temperature, Min -20 °C
Output Detail Current: 4 to 20 mA, 12 mA zero ± 8 mA outputs field programmable, Voltage: ± 5 volts, ± 10 volts at 2 mA maximum
Output Resistance 60 Ω
Protection Short Circuit Protection: Yes +output to -output
Response Time 200 µs
Response Time Note 200 µs (0 to 63%)
Sensitivity Bridge : 1 to 8 mV/V @ 5 Vdc EXC, 0.5 to 4 mV/V for 10 Vdc EXC
Sensor Excitation 5 or 10 Vdc field programmable; 30 mA @ 10 Vdc
Span Adjustment ± 20 % fine ± 40 % coarse
Supply Power 22 to 32 Vdc
Supply Power Note 22 to 32 Vdc isolated from output
Supply Power Type DC
Thermal Span Effect 0.0025%/°F
Thermal Zero Effect 0.001%/°F
Trim Pot Access Behind connector endcaps
Width 31.2 mm
Zero Setting Adjustable Range ± 30%

The OMEGA IN-UVI in-line signal conditioner is housed in a rugged stainless steel enclosure, which is connected between the transducer and a readout instrument. The signal conditioner supplies a highly regulated bridge excitation voltage for the transducer and converts the millivolt signal of the transducer to 0 to 5, 0 to 10, ± 5, ± 10 Vdc or 4 to 20, 12 ± 8 mA.
The IN-UVI features include two selectable excitation voltages, programmable gain amplifier for signals from 0.5 mV/V to 4 mV/V, wide zero adjustment range and an isolated shunt calibration relay for quick field setup. All output options and excitation voltages are field selectable. Ready-Made Cable Assemblies are now available to connect the IN-UVI to mV/V output sensors and to the power supply and display.

PDFs & Manuals

IN-UVI-Series_spec IN-UVI-Bridge-Amplifier View More

View Less

Accessories

cables

CA-4PC24-0-015-INUVI

Cable assembly, 4 conductor, PVC insulation, wiring code 0

$251.52

0 In Stock

QTY

CA-4PC24-2A-015-INUVI

Cable assembly, 4 conductor, PVC insulation, wiring code 2A

$251.52

0 In Stock

QTY

CA-4PC24-3-015-INUVI

Cable assembly, 4 conductor, PVC insulation, wiring code 3

$251.52

0 In Stock

QTY

CA-4PC24-4-015-INUVI

Cable assembly, 4 conductor, PVC insulation, wiring code 4

$251.52

0 In Stock

QTY

CA-4PC24-4A-015-INUVI

Cable assembly, 4 conductor, PVC insulation, wiring code 4A

$194.81

0 In Stock