Skip to search Skip to main content Skip to navigation

Click and hold to zoom

PX119

OEM Style, Compact Pressure Transmitters

4.8

(18)

Models In Stock

Compact and affordable for OEM applications
Easily configurable, now with expanded options
Reliable outputs with signal conditioning
Durable, stainless steel housing resists corrosion in harsh industrial environments

See Product Overview

PX119

From ^$ 122.43

Models In Stock

Shop Models

More Variations Available

See all series options below

Data Sheet

Product Overview

Accuracy ± 0.5 %
Accuracy Detail 0.50% BFSL Accuracy
Compensated Temperature, Max 85 °C
Compensated Temperature, Min 0 °C
Enclosure Material 304 Stainless Steel
Enclosure Ratings IP65
Materials, Wetted 304 Stainless Steel, Alumina, Buna-N (NBR)
Operating Temperature, Max 135 °C
Operating Temperature, Min -40 °C
Output Wiring (Pin 1) Supply +
Output Wiring (Pin 2) Supply -
Process Connection Type NPT Male
Protection Overvoltage, short circuit, reverse polarity
Response Time 1 ms
Stability <0.3% FS
Supply Voltage 8 to 30 Vdc
Weight 70 g

Pressure Without the Pain

Ideally suited for material handling, industrial and mobile equipment applications where a small, yet rugged SS body size is desired at a reasonable price point. The body is machined from a single piece of stainless steel to provide added protection for the internal electronics as well as prevent corrosion from most applications. A piezoresistive ceramic sensor along with ASIC signal conditioning provides an excellent thermally compensated output.

PX119 Low Cost SS Compact Pressure Transmitter

SIMPLE
MULTIPURPOSE
COMPACT

Monitor air brake pressure
Monitor pressure/height in vehicle suspension
Regulate pneumatic door operation

Monitor excessive load
Monitor lift operation
Monitor compact pressure

Great cost: performance ratio
Accuracy: 0.5% BFSL
Large pressure range
15 to 5000 psi (absolute or gauge)
Piezoresistive ceramic diaphragm
Excellent thermally compensated output
Operating temp: -40 to 135°C (32 to 185°F)
Reliable output with signal conditioning
Output: 4 to 20 mA or 0 to 5 Vdc
Input: 8 to 30 Vdc
Response time: 1 ms
Rugged form factor
Shock and vibration resistant
10g for <58 psi/20g for >58 psi
Resists corrosion and water
304 SS body
Wetted materials: Ceramic AI₂O₃, NBR

PDFs & Manuals

PX119_spec PX119 View More

View Less

Compliance

View Less

Reviews

Show Ratings & Reviews

4.8

(18)

Rated 5 out of 5 by Accidental Gardener from The Little Transmitter that could... I collect rain water in a 1000 L tote tank to use for my Greenhouse & several raised-beds. A small pump is used to recirculate the water not only to prevent stagnation but also for pH treatment to make it ready for use. The pump is then used for water delivery to the Greenhouse & raised-beds to reduce domestic water usage. This transmitter is great to monitor how well the pumping system performs. From bench testing before installation, I was very impressed with the response, repeatability & accuracy of this little unit. This is great as it does not have any zero/span adjustments. The pump has a low pressure, moderate flow delivery & I'm using a 15 psig transmitter (PX119-015GI). The Mini-DIN connector is great for easy disconnection as I will be bringing the pump & transmitter inside for the winter after the grow season is over.

Date published: 2020-08-29

Rated 4 out of 5 by dlyman from Awesome I needed a pressure transmitter and looked everywhere. I found very cheap to very expensive and long ship times. I ordered the Omega. I got it in 2 days and it has worked very well

Date published: 2018-05-14

Rated 4 out of 5 by Chris at FTS from Easy to Install and Use We purchased several of these in three different ranges. The first item is the ease of wiring the connector. Previous transducers used required soldering the wires to the connector terminals. There units have a simple screw lug that you simply insert the lead and screw tight in place. The time involved was less than half to complete connections. The transducers themselves work very well. My only minor concern is that the terminals on the transducer are exposed and can be bent easily. However, since there should be minimal need to remove the transducer connector, this is not a big concern.

Date published: 2019-03-06

Rated 5 out of 5 by Flaco from Pressure Transmitter This is a rugged little piece of equipment. I'ts accurate enough for what I'm doing, has held up to sub-optimal conditions and the price is unbeatable.

Date published: 2019-02-05

Rated 5 out of 5 by KA8008 from Good Quality Good- Solid Product. Where i work we test HVAC Units these are a must have

Date published: 2024-04-08

Rated 5 out of 5 by J Wales from Exactly fit my specs. Needed item in stock, easily ordered and quickly shipped.

Date published: 2024-03-12

Rated 5 out of 5 by J Wales from Exactly what was needed, quickly shipped! Upgrading my instrument panel to full EFIS required the installation of pressure transducers with specific parameters. This device at Omega was the first that I located which completely fit my requirements. It also turned out to be the most affordable. The order was easily placed with Omega and the item shipped within just a couple of days. Since the aircraft is still undergoing the upgrade, I can’t address the transducer’s reliability, but the installation was straightforward and preliminary checks show it to be functioning correctly.

Date published: 2024-03-12

Rated 4 out of 5 by evic from amazing Quick and accurate to respond queries every time I placed an order or request for a quotation

Date published: 2023-11-23

0 to 15 psi, Absolute Pressure, 0 to 5 Vdc Output, 1/4"NPT Male, Cable Connection Reviews - page 2

Questions & Answers

Videos & Downloads

PX119

OEM Style, Compact Pressure Transmitters

Pressure Without the Pain

I need to use this pressure sensor to get data from a pneumatics braking system on a small vehicle. We are using an arduino to collect data. Adruinos can measure between 0-5 V DC but it cannot measure current directly. Can it be used for this application?

Are these National Sanitation Foundation (NSF) certified?

CAD model available?

Can the PX119 be used to measure hydraulic pressure? 2250 psi max

When we connect pressurized air to a PX119-150AI transducer, air is leaking out the back of the transducer around the electical connector. This is not the behavior we expected. Please explain why air pressure is leaking through the sensor.

Is the 3D CAD available? I need info on the threads for the installation setup.

Can these transducers be install within a test article that is then placed within a pressure chamber; and have the pressure in the pressure chamber is to be increased up to 75 PSIA, while the transducer(s) monitor the pressures within the unit?

For the PX109A-030A5V, which has a cable connection, is the recommended cable accessory (CA-319-4PC24-XXX-WP) necessary?