1-800-663-4209 | Welcome to our new website, found an issue or bug? Please report it here
DP7600-Series
High Speed Load/Strain Meters and Process/Voltmeters
Models In Stock
- 5-Digit Display
- Dual Inputs Available
- All Programming and Calibrating Via 5 Front Panel Switches
- Programmable Digital Filter, 1 to 500 Hz Cutoff
DP7600-Series
From
$
1,404.07
Models In Stock
Product Overview
- Accuracy ± 0.01 %
- Accuracy Detail ± 0.01% of reading ± 1 count of A/D @ 25°C (77°F)
- Channels One channel standard, second channel optional
- Convert/Hold Input Normally high; if pulled low, holds display
- Cutout Dimensions 2.45 x 5.06 in
- Digital Filter Programmable Cutoff Frequency
- Display Note -32768 to 32767 with programmable decimal points; 14 mm (0.56") red LED
- Display Type LED
- Electrical Connection Screw Terminal
- Form factor 1/8 DIN
- Height 2.7 in
- Input Analog Filter 4-pole active anti-alias; 500 Hz cutoff on single-channel unit and 250 Hz cutoff on dual-channel unit
- Input Bias Current ± 50 nA maximum ± 100 pA/°C (per input channel)
- Input Configuration Front Keypad
- Internal Resolution 16 bit
- Length 6.9 in
- Measurement Type Current, Strain, Voltage
- Mounting Panel
- Number of Digits 5
- Number of Inputs 1
- Operating Temperature, Max 60 °C
- Operating Temperature, Min -20 °C
- Output Method RJ11 jack for serial interface
- Peak Detection Updated at rate selected by digital filter, peak stored in memoryrogrammed to give limit #1 output up to 100 seconds after a programmed limit is reached. This output can be used to reset the peak reading by tying limit #1 output to remote input
- Power Consumption 8 W
- Reading Rate Limited to 1000/s divided by number of channels
- Remote Inputs Display Peak, Display Runout, Reading, Reset Peak, Runout Reading, Tare
- Resolution 16-bit A/D
- Rollover Error ± 2 counts of A/D @ 25°C (77°F)
- Runout Mode Updated at rate selected by digital filter. Runout is normally stored in memory and recalled via front-panel switch, over the serial interface, or by selecting runout display mode on rear connector.
- Sampling Rate 1000 Hz
- Sensor Excitation ± 15 Vdc, ± 5 Vdc @ ± 50 mA
- SetPoint Outputs 4 isolated open collector transistor outputs rated 30 Vdc maximum; will sink up to 50 mA; 300 V isolation between limit outputs and system ground; limit #1 can be programmed to be delayed from 1 to 100 seconds
- Settable Parameters Digital Filter, Limits, Offset, Span
- Weight 370 g
- Width 5.18 in
The DP7600 is a high speed load/strain meter. The unit performs 1000 conversions per second with limit checking and peak/runout tracking done at a user selectable rate (from 1 to 500 Hz). Peak and runout data can also be displayed using the front panel switches. A tare reading, up to 50% of span, can be entered with a single front panel push button.
The DP7700 is a high speed process/voltmeter with many of the same features. The DP7700 accepts most process inputs from 0-200 mV to 0-10 Vdc and 4-20 mA current loops. Transducer/loop power of ± 15 Vdc @ 50 mA is standard.
Programming both meters is accomplished via five switches located on the front panel. The text at the top of the switch (NORMAL, PEAK, RUNOUT, TARE, ABS/REL) indicates its normal function. The text at the lower half of the switch (ENTER, UP, DOWN, NEXT, EXIT) indicates the switch’s function during setup and calibration.
The DP7700 is a high speed process/voltmeter with many of the same features. The DP7700 accepts most process inputs from 0-200 mV to 0-10 Vdc and 4-20 mA current loops. Transducer/loop power of ± 15 Vdc @ 50 mA is standard.
Programming both meters is accomplished via five switches located on the front panel. The text at the top of the switch (NORMAL, PEAK, RUNOUT, TARE, ABS/REL) indicates its normal function. The text at the lower half of the switch (ENTER, UP, DOWN, NEXT, EXIT) indicates the switch’s function during setup and calibration.
PDFs & Manuals
Show Ratings & Reviews