1-800-663-4209 | Welcome to our new website, found an issue or bug? Please report it here
AHPF-HEATER
316 SS Inline Duct Heater up to 800 °F and 1.2 kW Power-Liq
Models In Stock
- 316 Stainless Steel Construction
- Air/Gas Flow up to 15 CFM
- Air/Gas Outlet Temperatures up to 800°F (430°C)
- Pressures up to 100 PSI*
AHPF-HEATER
From
$
637.33
Models In Stock
Product Overview
- Air Flow, Max 15 CFM
- Mounting Inline
- Outer Diameter 1.25 in
- Outlet Air Temperature, Max 430 °C
- Port 1 Size 3/8 in
- Port 1 Type NPT Male
- Port 2 Size 1/2 in
- Port 2 Type NPT
- Power Tolerance +5, -10%
- Sheath Material 316 Stainless Steel
The AHPF series heaters are used to heat low flows of air, gas, water, or aqueous solutions. Applications include those where clean air is necessary, as in laboratories and environmental testing areas. The stream of air is heated by passing over an enclosed heated surface rather than directly over resistance elements. This method assures that no foreign matter will enter the stream of flow. The AHPF series is also used as a miniature circulation heater for small volume liquids as in photographic developer solution, chemicals, dyes, and inks. Calculate the flow rate, temperature rise, or power requirement as described on page J-17. For heating liquids, use the formulas on pages Z-10 or Z-41. The Thermocouple "T" fitting AHPF-NPT12 can be used with the subminiature thermocouple probes and with the SSLK series stainless steel compression fittings (see the OMEGA Complete Temperature Measurement Handbook and Encyclopedia®) and with stainless steel compression fittings (model SSLK-18-14) to monitor or control temperature at the outlet of the AHPF series heaters.
SPECIFICATIONS
Cross Sectional Area: 0.152 sq. inches
Pressure Rating: Up to 100 PSIG
Wattage Tolerance: +5, -10% or better at the voltage specified
Outside Diameter: 11/4' (32 mm)
Inlet: Male 3/8' NPT
Outlet: 1/2' NPT
Read More
SPECIFICATIONS
Cross Sectional Area: 0.152 sq. inches
Pressure Rating: Up to 100 PSIG
Wattage Tolerance: +5, -10% or better at the voltage specified
Outside Diameter: 11/4' (32 mm)
Inlet: Male 3/8' NPT
Outlet: 1/2' NPT
| Model Number | Volts | Watts | Heated Length in (mm) | Watts/Inch* | Maximum CFM | Length in (mm) | Weight lb (kg) |
| 120 VAC Models | |||||||
| AHPF-061 | 120 | 400 | 4 (102) | 91 | 15 | 6 (152) | 1.00 (0.45) |
| AHPF-081 | 120 | 600 | 6 (152) | 94 | 15 | 8 (203) | 1.18 (0.54) |
| AHPF-101 | 120 | 1000 | 8 (203) | 120 | 15 | 10 (254) | 1.37 (0.62) |
| AHPF-121 | 120 | 1200 | 10 (254) | 115 | 15 | 12 (305) | 1.55 (0.70) |
| 120/240 VAC Models** | |||||||
| AHPF-062 | 120 240 | 100 400 | 4 (102) 4 (102) | 23 91 | 15 15 | 6 (152) | 1.00 (0.45) |
| AHPF-082 | 120 240 | 150 600 | 6 (152) 6 (152) | 23 94 | 15 15 | 8 (203) | 1.18 (0.54) |
| AHPF-102 | 120 240 | 250 1000 | 8 (203) 8 (203) | 30 120 | 15 15 | 10 (254) | 1.37 (0.62) |
| AHPF-122 | 120 240 | 300 1200 | 10 (254) 10 (254) | 29 115 | 15 15 | 12 (305) | 1.55 (0.70) |
| *Indicates Watts per inch of heated length. Use the table above to determine minimum required flow rates. **These air heaters can be operated on either 120 or 240 Volts. Specifications are shown for either 120 or 240 Volt operation. |
PDFs & Manuals
