DP6000

0.0

(0)

Models In Stock

See Product Overview

DP6000

From ^C$ 1,161.90

Models In Stock

Shop Models

10 Variations available

See all series options below

Data Sheet

Product Overview

Baud Rate 300 to 19200
Calibration Calibrated at the factory. Recalibration is recommended at least every 12 months
Category of Overvoltage II
Category of Overvoltage Note Installation overvoltage category II; local level with smaller transient overvoltages than installation overvoltage category III
Data Interface Modbus RTU
Data Interface Note Protocol: Modbus RTU Meter Address/Slave ID: 1 – 247 Baud Rate: 300 to 19,200 bps Transmit Time Delay: Programmable between 0 and 199 ms Data: 8 bit (1 start bit, 1 or 2 stop bits) Parity: Even, odd, or none with 1 or 2 stop bits Byte-to-Byte Timeout: 0.01 to 2.54 seconds Turn Around Delay: Less than 2 ms (fixed)
Digital I/O Note Channels: 4 digital inputs and 4 digital outputs per module System: Up to 2 modules for a total of 8 inputs and 8 outputs Digital Input Logic: High: 3 to 5 Vdc Low: 0 to 1.25 Vdc Digital Output Logic: High: 3.1 to 3.3 Vdc Low: 0 to 0.4 Vdc Source Current: 10 mA maximum Sink Current: 1.5 mA minimum +5 V Terminal: To be used as pull-up for digital inputs only
Display Color Red
Display Size 15 mm (0.60 in)
Electrical Connection Screw Terminal
Electrical Connection Note Removable screw terminal blocks accept 12 to 22 AWG wire, RJ45 for external relays, digital I/o, and serial communication adaptors
Enclosure Material Plastic
Enclosure Ratings IP65, NEMA Type 4X
Form factor 1/8 DIN
Functions Noise Filter: Programmable from 2 to 199 (0 will disable filter) ;Filter Bypass: Programmable from 0.1 to 99.9% of calibrated span ;Cyber Security: 3 programmable passwords restrict modification of programmed settings; Pass 1: Allows use of function keys and digital inputs; Pass 2: Allows use of function keys, digital inputs and editing set/ reset points; Pass 3: Restricts all programming, function keys, and digital inputs
Fuse Rating 5 A delayed
Height 62 mm
Input Type Note Input: Field selectable: 0 to 20 mA, 4 to 20 mA, ±10 Vdc (0 to 5, 1 to 5, 0 to 10V), MoDbuS PV (slave) Accuracy: ±0.03% of calibrated span ±1 count, square root and programmable exponent accuracy range: 10 to 100% of calibrated span Temperature Drift: 0.005% of calibrated span/°C max from 0 to 65°C ambient, 0.01% of calibrated span/°C max from -40 to 0°C ambient Signal Input Conditioning Function: Linear, square root, programmable exponent, or round horizontal tank volume calculation Multi-Point Linearization: 2 to 32 points for PV or PV1; 2 to 8 points for PV2 (dual-scale level feature) Programmable Exponent: 1.0001 to 2.9999 Low-Flow Cutoff: 0 to 999999 (0 disables cutoff function) Decimal Point: Up to 5 decimal places or none: d.ddddd, dd.dddd, ddd.ddd, dddd.dd, ddddd.d, or dddddd Calibration Range: 4 to 20 mA: Minimum span; input 1 and Input 2: 0.15 mA ±10 V: Minimum span; input 1 and 2: 0.10 V An Error message will appear if input 1 and input 2 signals are too close together Input Impedance: Voltage Ranges: Greater than 1 MΩ Current Ranges: 50 to 100 Ω (depending on resettable fuse impedance) Input Overload: Current input protected by resettable fuse, 30 Vdc max; fuse resets automatically after fault is removed
Isolation 4 kV input/output-to-power line; 500 V input-to-output or output-to-P+ supply
Length 143 mm
Memory Non-Volatile Memory : All programmed settings are stored in non-volatile memory for a minimum of ten years if power is lost
Mounting 1/8 DIN panel cutout required: 92 x 45 mm (3.622 x 1.772"); two panel mounting bracket assemblies are provided
Normal Mode Rejection Greater than 60 db at 50/60 Hz
Operating Temperature, Max 65 °C
Operating Temperature, Min -40 °C
Programmable Functions Filter Bypass, Noise Filter, Security
Programming 4 front panel buttons, digital inputs, PC and software, Modbus registers, or cloning using copy function
Relative Humidity 0 to 90% non-condensing
Sampling Rate 5 Hz (5 updates/second)
Series ID DP6000
Storage Temperature, Max 85 °C
Storage Temperature, Min -40 °C
Supply Power Note 85 to 265 Vac 50/60 Hz, 90 to 265 Vdc, 20 W max, or jumper selectable 12/24 Vdc ±10%, 15 W max Isolated Transmitter Power Supply: 24 Vdc ±5% @ 200 mA max (standard), (12/24 Vdc powered models rated @ 100 mA max); 5 or 10 Vdc @ 50 mA max, selectable with internal jumper J4
Tightening Torque Screw terminal connectors: 5 lb-in
Weight 269 g
Width 119 mm
Wire Gauge 22 to 12 AWG