検索へジャンプ メインコンテンツへジャンプ ナビゲーションへジャンプ

日本 +81 3 6822 0370 | 新しいウェブサイトへようこそ。問題やバグを見つけましたか?こちらからご報告ください

におられるようです。地域限定のオファーやサポートをご希望の場合は、下のリンクをクリックして、お住まいの地域のサイトにアクセスしてください。

PUR-TX-3W

Pura トランスミッター

  • -120 °Cdp(-184 °Fdp)(1ppbV)まで測定
  • 安定した再現性のある測定
  • 高速応答
PUR-TX-3W
販売元
Pura トランスミッター PUR-TX-3W PUR-TX-3W
loading all models
製品の概要
  • 精度の詳細 ±1 °C(-40 ~ -60 °Cdpの範囲)(±1.8 °F(-40 ~ -76 °Fdpの範囲)); ±2 °C(-60 ~ -100 °Cdpの範囲)(±3.6 °C(-76 ~ -148 °Fdpの範囲)); ±4 °C(-100 ~ -120 °Cdpの範囲)(±7.2 °C(-148 ~ -184 °Fdpの範囲、外挿値))
  • 校正に関する注記 トレーサブル7点校正証明書
  • 補償温度、最大 50 °C
  • 補償温度、最小 -20 °C
  • コンプライアンスに関する注意事項 ATEX/UKCA: II 1 G Ex ia IIC T4 Ga (-20...+70 °C) IECEx: Ex ia IIC T4 Ga (-20...+70 °C) TR CU: 0Ex ia IIC T4 Ga (-20...+70 °C) cQPSus: Class I, Division 1, Groups A, B, C & D, T4 Class I, Zone 0, AEx ia IIC T4 Ga, Ex ia IIC T4 Ga Tamb +70 °C
  • 電気接続 Mini DIN 43650 C
  • 電気出力 0~20 mA
  • エンクロージャーの定格 IP66, NEMA タイプ 4
  • 工場出荷時設定 センサー故障:23 mA;アンダーレンジ露点:4 mA;オーバーレンジ露点:20 mA
  • 流量に関する注記 1...5 Nl/min 標準サンプリングブロックに取り付け; 0...10 m/sec 直接挿入
  • ガルバニック絶縁 FD0-CS-EX1.50P、KFD0-CS-EX2.50P、KFD2-STC4-EX1.H
  • ハウジング材質 316ステンレス鋼
  • 荷重抵抗 最大250 Ω @ 14 V(500 Ω @ 24 V)
  • 測定タイプ 露点、湿度
  • ワイヤ本数 3
  • 動作圧力(最大) 24 MPa
  • 動作温度(最高) 60 °C
  • 動作温度(最低) -40 °C
  • プロセス接続タイプ VCR オス
  • シリーズID PUR-TX-3W
  • 最大保管温度 60 °C
  • 保管温度(最低) -40 °C
  • 供給電流 23 mA
  • 供給電圧 12から28Vdc
  • 温度測定範囲 -120Cから-40°C

Supported Applications

The PUR-TX-3W is a Pura Transmitter configured for a 3-wire 4-20mA connection, built for the measurement of trace moisture in ultra-high purity gases. It reports dew-point moisture content and is suited to demanding industrial gas streams where very low water content must be tracked continuously.

Compatible media documented for the Pura range include Ultra-high purity gases and UHP inert gas, as well as Natural Gas, LPG, Hydrogen, Nitrogen, Air, Inert Gases and Hydrocarbons. The analog output can be scaled across a dew point of -120...-40 °C or, for moisture content in gas, across 0...127 ppmₕ, making the transmitter appropriate for both dew-point and concentration-based monitoring tasks.

Operating Conditions & Performance

The transmitter measures across a dew-point range of -120 to -40°C. Accuracy is specified in tiers: ±1 °C from -40 to -60 °Cdp, ±2 °C from -60 to -100 °Cdp, and ±4 °C from -100 to -120 °Cdp (extrapolated). Repeatability is ±0.5% of reading, resolution is 0.1 ppmv, and the response time is T90 < 10 seconds. Each unit ships with a traceable 7-point calibration certificate.

In its 3-wire form the device delivers a 4...20 mA output (3-wire connection, current sink). Supply voltage is 12...28 V DC, load resistance is Max 250 Ω @ 14 V (500 Ω @ 24 V), and current consumption is up to 23 mA max. Electrical termination uses a MiniDIN 43650 form C or M12 5-pin (A coded) connector.

Operating temperature is -40...+60 °C, with an ambient range of -20...+50 °C and storage at -40...+60 °C. Maximum process pressure is 24 MPa. The enclosure carries an IP66 rating in accordance with BS EN 60529:1992 and NEMA 4 protection in accordance with NEMA 250-2003. Wetted parts are 316 stainless steel, and process connections are offered as 1/2" male VCR and 1/4" male VCR.

Configuration Options

Both models in this series share the 3-wire 4-20mA architecture (parent code PUR-TX-3W) and the same -120 to -40°C dew-point range (range code A), but they differ in mechanical build and packaging.

  • PUR-TX-3W-BA is the OEM (Single Bagged) build. As an OEM version it includes the sample block and has a documented weight of 450 g.
  • PUR-TX-3W-CA is the SEN (Sensor only, no block) build. Without the sample block it is the lighter option at 180 g, intended for integration into an existing block or system.

The sensor-only configuration trades the integral sample block for a lower mass and simpler footprint, while the OEM build is supplied ready-mounted. Recalibration is handled through matching service codes — PUR-TX-OEM-Recal for the OEM build and PUR-TX-SEN-Recal for the sensor-only build — each providing 13 points between -100 and +20°C dp with a certificate traceable to national standards.

Key Product Differences

The PUR-TX-3W lineup consists of two orderable models, both derived from the Pura Transmitter 3-wire 4-20 mA base (PUR-TX-3W):

  • PUR-TX-3W-BA — OEM (Single Bagged) version, -120 to -40°C dp range.
  • PUR-TX-3W-CA — SEN (Sensor only, no block) version, -120 to -40°C dp range. The documented ordering example describes this as "Pura Transmitter 4-20mA 3 wire, Sensor only, no block, range -120 to -40°C".

Supporting accessories documented for the range include M12 sensor cables (for example EA2-M12-CAB-02 and EA2-M12-CAB-05), MiniDIN cable assemblies, and a Service Exchange path under parent code PUR-TX-X for cost-managed sensor replacement.

ja-JP
ko_KR
設定を保存する