日本 +81 3 6822 0370 | 新しいウェブサイトへようこそ。問題やバグを見つけましたか?こちらからご報告ください
Series-DH
多機能差圧コントローラー、精度0.5%、デジタル表示
다기능 차압 컨트롤러, 0.5% 정확도, 디지털 디스플레이
在庫のあるモデル
- 3-in-1 기기는 여러 기기를 하나의 제품으로 대체하여 재고, 설치 시간 및 비용 절감이 가능합니다
- 유속 모드에서 제곱근 출력은 실제 유량 곡선과 일치하여 더 높은 정밀도를 제공합니다
- 120/220 Vac 또는 24 Vdc 전원 사용으로 제어판에 장치 통합 유연성을 제공합니다
- 보안 메뉴 프로그램은 적절한 숙련 수준에만 장치 작동 접근 권한을 부여합니다
- Modbus® 통신은 프로세스 및 HVAC 시스템 통합 및 제어를 지원합니다
製品の概要
- 정확도 세부 사항 ± 0.5% 에서 77 °F (25 °C) 히스테리시스 및 반복성을 포함하여.
- 전송 속도 9600
- 최대 보상 온도 140 °F
- 최소 보상 온도 32 °F
- 데이터 인터페이스 Modbus RTU, RS485
- 디스플레이 노트 4자리 LCD 0.4" 높이. 설정값 및 알람 상태용 LED 표시등
- 디스플레이 유형 LCD
- 전기 연결 나사 단자
- 외함 등급 IP66, NEMA 타입 4X
- 높이 3.62 in
- 길이 1.772 in
- 재료 ABS
- 접액부 재질 컨설트 팩토리
- 미디어 호환성 깨끗한 건조 공기 / 불활성 가스, HVAC / 실내 공기, 비활성 가스/비반응성 가스
- 장착 1/8 DIN
- 장착 방향 수평
- 표시 자릿수 4
- 작동 온도, 최대 140 °F
- 최소 작동 온도 32 °F
- 출력 세부 정보 4~20 mA DC, 최대 900 Ω 부하
- 출력 신호 현재
- 전력 소비 7 VA, 저전력: 130 mA
- 압력 유형 차동
- 프로세스 연결 사양 참고 1/8˝ ID X 1/4˝ OD 튜빙(3.175 mm ID x 6.35 mm OD)용 압축 피팅. 3/16˝ ID 튜빙용 선택형 바브 피팅.
- 프로세스 연결 크기 1/8인치
- 프로세스 연결 유형 압축 피팅
- 응답 시간 250 ms
- 시리즈 ID Series-DH
- 설정 지점 조정 메뉴 구성 가능
- 안정성 <± 1%/년
- 공급 전력 참고 고전압 전원 = 100-240 Vac, 50-400 Hz 또는 132-240 Vdc, 저전압 전원 = 24 Vdc ± 20%.
- 전원 유형 AC / DC
- 공급 전압 100 ~ 240 Vac, 132 ~ 240 Vdc
- 스위치 사양 참고 240 Vac 저항 부하에서 8 A
- 스위치 등급 8 A @ 240 Vac
- 스위치 유형 (2) SPDT
- 열 효과 77 °F에서 0.020%/°F
- 무게 14.4 oz
- 제로 설정 조절 범위 메뉴를 통해 접근 가능
Supported Applications
The Dwyer Series DH Digihelic® Differential Pressure Controller is a multifunction instrument designed for measuring and controlling differential pressure in air and non-combustible, compatible gases. The series functions as a digital display gage, control relay switch, and transmitter with current output. It supports operation modes for pressure, velocity, and volumetric flow applications across various engineering units.
Operating Conditions & Performance
The Series DH achieves an accuracy of ±0.5% at 77°F (25°C) including hysteresis and repeatability after a 1-hour warm-up period. The instrument operates within an ambient temperature range of 32 to 140°F (0 to 60°C). Response time is specified as 250 ms with dampening set to 1.
Measurement ranges span from 0.25 in w.c. up to 100 in w.c., available via specific model selection for unidirectional and bi-directional spans. Pressure ratings vary by range: models ≤ 2.5 in. w.c. are rated at 2 psi; the 5, 10, and 25 in. w.c. ranges are rated at 5 psi; and the 50 and 100 in. w.c. ranges are rated at 9 psi.
Available Engineering Units
The controller allows selection of multiple engineering units for display, including:
- Pressure: INWC (inches water column), FTWC, MMWC, CMWC, PSI, INHG, MMHG, MBAR, PA, KPA, HPA, OZIN.
- Velocity/Flow: SFPM, M/S, SCFM, M^3H.
Configuration Options
The series offers configurable options for process connections, calibration documentation, and mounting. The standard enclosure is ABS plastic (UL approved 94-V-0) with a face designed to meet NEMA 4X (IP66). Electrical connection utilizes screw terminals.
Power Supply Options
- High Voltage: 100 to 240 VAC, 50 to 400 Hz or 132 to 240 VDC.
- Low Voltage: 24 VDC ±20%.
Output Signals & Communication
- Analog Output: Scalable 4-20 mA DC into a maximum load of 900 Ω (typical 250 to 600 OHMS).
- Digital Communication: Modbus® Protocol RTU over RS485 at 9600 Baud. The factory default address is 50.
Process Connections & Options
The standard process connection is a compression fitting for use with 1/8" ID tubing x 1/4" OD tubing (3.175 mm ID x 6.35 mm OD). An optional barbed fitting (-B) is available for 3/16" ID tubing.
Additional options include:
- -FC: Factory calibration certificate.
- -NIST: NIST traceable calibration certificate.
Key Product Differences
The Series DH is available in specific model numbers corresponding to distinct pressure ranges. Models are categorized by unidirectional and bi-directional capabilities, with velocity and volumetric flow modes not available on bi-directional range units or models DH-009 and DH-010.
Unidirectional Range Models
- DH-002: 0 to 0.25 in w.c.
- DH-004: 0 to 1.0 in w.c.
- DH-006: 0 to 5 in w.c.
- DH-007: 0 to 10 in w.c.
- DH-008: 0 to 25 in w.c.
- DH-009: 0 to 50 in w.c. (Pressure only).
- DH-010: 0 to 100 in w.c. (Pressure only).
Bi-directional Range Models
- DH-012: ±0.25 in w.c.
- DH-014: ±1.0 in w.c.
- DH-015: ±2.5 in w.c.
- DH-016: ±5.0 in w.c.
- DH-017: ±10 in w.c.