검색으로 이동 메인 콘텐츠로 이동 탐색으로 이동

한국 1588-8983 | 새로운 웹사이트에 오신 것을 환영합니다. 문제나 버그를 발견하셨나요? 여기에 보고해주세요

현재 에 계신 것을 확인했습니다. 아래 링크를 클릭하여 지역 사이트를 방문하시면, 지역별 특가 혜택과 지원 서비스를 받으실 수 있습니다.

EA34-TX

Easidew 2선 이슬점 트랜스미터

  • 측정 범위 -110에서 +20°Cdp까지
  • 이슬점 또는 ppm V 수분 함량 출력
  • 정확도 ±2 °Cdp
  • 3/4” UNF 프로세스 연결
EA34-TX
시작 2,792,099 원
Easidew 2선 이슬점 트랜스미터 EA34-TX EA34-TX
loading all models
제품 개요
  • 액세서리 유형 5/8" 18 UNF 및 3/4" 16 UNF 공정 연결용 플랜지
  • 정확도 ± 2 °C (± 3.6 °F)
  • 정확도 세부 사항 ±2°C (±3.6°F) 이슬점*
  • 응용 분야 항공, 에어 드라이어, 화학 정제소, 클린 룸, 깨끗한 물과 정제된 용액, 압축기 제어, 필터 모니터링, 유량 측정, 가스, HVAC, 산업 및 제조업, 천연가스 압축기, 발전소 및 보일러, 연구개발/엔지니어링 테스트, 냉장, 냉동 장비, 온도 유지, 폐수 처리 응용
  • 보정 사양 참고 추적 가능한 13점 교정 증명서
  • 최대 보상 온도 50 °C
  • 최소 보상 온도 -20 °C
  • 규정 준수 노트 ATEX/UKCA: II 1 G Ex ia IIC T4 Ga (-20 ~ +70 °C) IECEx: EX ia IIC T4 Ga (-20 ~ +70 °C) TR CU @ 0Ex ia IICT4 Ga (-20 ~ +70 °C) cQPSus: Class I, Division 1, Groups A, B, C & D, T4 Class I, Zone 0, AEx ia IIC T4 Gb, Ex ia IIC T4 Gb Tamb +70 °C
  • 전기 출력 4 ~ 20 mA
  • 외함 등급 IP66, NEMA 타입 4
  • 공장 설정 센서 고장: 23 mA; 저범위 이슬점: 4 mA; 고범위 이슬점: 20 mA
  • 유량 노트 1~5 Nl/min 표준 샘플링 블록에 장착; 0~10 m/sec 직접 삽입
  • 갈바닉 절연 KFD2-CR-EX1.20200,KFD2-CR-EX1.30200,KFD0-CS-EX1.50P,KFD0-CS-EX2.50P,KFD2-STC4-EX1.H,MTL5041,MTL5040
  • 하우징 재질 316 스테인리스 스틸
  • 하중 저항 최대 250 Ω @ 14 V (500 Ω @ 24 V)
  • 측정 유형 이슬점, 습도
  • 최대 작동 압력 52.5 MPa
  • 작동 온도, 최대 60 °C
  • 최소 작동 온도 -40 °C
  • 프로세스 연결 크기 3/4인치
  • 프로세스 연결 유형 UNF 수나사
  • 반복성 0.5°C (0.9°F) 이슬점
  • 응답 시간 T95까지 5분 (건조에서 습윤까지)
  • 시리즈 ID EA34-TX
  • 저장 온도, 최대 60 °C
  • 보관 온도 최소 -40 °C
  • 공급 전류 23 mA
  • 공급 전압 12 ~ 28 Vdc
  • 무게 150 g

Supported Applications

The EA34-TX Series is the 3/4" UNF version of Michell Instruments' Easidew 2-wire dew-point transmitter, a compact loop-powered instrument for measuring moisture content in gases. Delivering its reading as a standard current signal, it threads directly into a process line or sample block and reports dryness continuously to a controller, PLC, or monitoring system.

It is well suited to natural gas, hydrogen, nitrogen, air, and inert gas systems, and to compressed-gas drying where product quality depends on low moisture. The 3/4" UNF thread makes the EA34-TX a straightforward fit for common sample-block and adapter fittings, giving reliable, long-term dew-point monitoring.

Operating Conditions & Performance

The transmitter measures dew point over -110 to +20°C (-166 to +68°F), with a companion range of -100 to +20°C (-148 to +68°F), resolving readings to 0.01 °C. It holds an accuracy of ±0.5 °C / ±0.9 °F with a repeatability of ±0.2 °C, and provides a typical T90 response of less than 10 seconds.

Output is a 4–20 mA loop signal with RS485 / Modbus RTU communications, powered from 10–30 VDC into a load of up to 500 Ω at 24 VDC, terminated through a DIN 43650 or M12 connector. The sensor withstands pressures up to 45 MPa (450 barg / 6500 psig), and its wetted parts use 316L stainless steel with an HMWPE guard.

The EA34-TX carries an IP67 enclosure and operates over a process range of -100 °C to +100 °C, an ambient range of -40 °C to +85 °C, and storage to -40 °C to +85 °C. The probe measures 12 mm in diameter with a 25 mm insertion length, a 50 mm stem, and a 100 mm overall length. Approvals include ATEX, IECEx, UL, CSA, and NEC.

Configuration Options

The EA34-TX is ordered as a configured transmitter on a fixed 3/4" UNF thread, with a letter-based code that fixes each remaining feature to the application. The configurable axes are:

  • Range — a -100 to +20°C or -110 to +20°C dew-point range, or a non-standard configured range in °C, °F, or ppmV.
  • Protection — a standard HDPE guard against fine particulates, or a stainless-steel sintered guard.
  • Oxygen cleaning — standard, or cleaned for oxygen service, which is offered only with the stainless-steel sintered guard.

Because the process thread is fixed, the choices that change the delivered instrument are the guard type and oxygen-cleaning selection, which together govern particulate protection and suitability for oxygen-enriched media, while the range option sets the span over which the transmitter is scaled.

Key Product Differences

Ordering follows the parent code and its three feature positions, EA34-TX - <Range> - <Protection> - <Oxygen Cleaning>. The lineup spans the letter combinations from EA34-TX-AAA through EA34-TX-BBA, for example:

  • EA34-TX-ABB — Easidew 2-wire transmitter with the -100 to +20°C range, a stainless-steel sintered guard, and oxygen-cleaned wetted parts.
  • EA34-TX-RAA — non-standard range built to customer specification with an HDPE guard and no oxygen cleaning; the range is specified at time of order.

Under the previous ordering system the same choices were expressed as the base model plus feature codes for range, guard, and oxygen cleaning. Across every configuration the core sensing platform and 3/4" UNF thread stay the same — the model number simply records the chosen range, guard, and oxygen-cleaning options.

ko-KR
ko_KR
설정 저장