검색으로 이동 메인 콘텐츠로 이동 탐색으로 이동

한국 1588-8983 | 새로운 웹사이트에 오신 것을 환영합니다. 문제나 버그를 발견하셨나요? 여기에 보고해주세요

현재 에 계신 것을 확인했습니다. 아래 링크를 클릭하여 지역 사이트를 방문하시면, 지역별 특가 혜택과 지원 서비스를 받으실 수 있습니다.

EA2-TX

Easidew 2선 이슬점 트랜스미터

  • 측정 범위 -110에서 +20 °Cdp
  • 이슬점 또는 ppmV 수분 함량 출력
  • 정확도 ±2 °Cdp
EA2-TX
시작 2,792,099 원
Easidew 2선 이슬점 트랜스미터 EA2-TX EA2-TX
loading all models
제품 개요
  • 액세서리 유형 5/8" 18 UNF 및 3/4" 16 UNF 공정 연결용 플랜지
  • 정확도 ± 2 °C (± 3.6 °F)
  • 정확도 세부 사항 ±2°C (±3.6°F) 이슬점
  • 응용 분야 항공, 에어 드라이어, 화학 정제소, 클린 룸, 깨끗한 물과 정제된 용액, 압축기 제어, 필터 모니터링, 유량 측정, 가스, HVAC, 산업 및 제조업, 천연가스 압축기, 발전소 및 보일러, 연구개발/엔지니어링 테스트, 냉장, 냉동 장비, 온도 유지, 폐수 처리 응용
  • 보정 사양 참고 추적 가능한 13점 교정 증명서
  • 최대 보상 온도 50 °C
  • 최소 보상 온도 -20 °C
  • 규정 준수 노트 ATEX/UKCA: II 1 G Ex ia IIC T4 Ga (-20 ~ +70 °C) IECEx: EX ia IIC T4 Ga (-20 ~ +70 °C) TR CU @ 0Ex ia IICT4 Ga (-20 ~ +70 °C) cQPSus: Class I, Division 1, Groups A, B, C & D, T4 Class I, Zone 0, AEx ia IIC T4 Gb, Ex ia IIC T4 Gb Tamb +70 °C
  • 치수 노트 MiniDIN 43650 형태 C L=132mm x ø45mm (커넥터 케이블 포함)
  • 전기 연결 미니 DIN 43650 C
  • 전기 출력 4 ~ 20 mA
  • 외함 등급 IP66, NEMA 타입 4
  • 공장 설정 센서 고장: 23 mA; 저범위 이슬점: 4 mA; 고범위 이슬점: 20 mA
  • 유량 노트 1~5 Nl/min 표준 샘플링 블록에 장착; 0~10 m/sec 직접 삽입
  • 갈바닉 절연 KFD2-CR-EX1.20200,KFD2-CR-EX1.30200,KFD0-CS-EX1.50P,KFD0-CS-EX2.50P,KFD2-STC4-EX1.H,MTL5041,MTL5040
  • 높이 132 mm
  • 하우징 재질 316 스테인리스 스틸
  • 길이 45 mm
  • 하중 저항 최대 250 Ω @ 14 V (500 Ω @ 24 V)
  • 최대 작동 압력 52.5 MPa
  • 작동 온도, 최대 60 °C
  • 최소 작동 온도 -40 °C
  • 프로세스 연결 크기 5/8인치
  • 프로세스 연결 유형 UNF 수나사
  • 반복성 0.5°C (0.9°F) 이슬점
  • 응답 시간 T95까지 5분 (건조에서 습윤까지)
  • 시리즈 ID EA2-TX
  • 저장 온도, 최대 60 °C
  • 보관 온도 최소 -40 °C
  • 공급 전류 23 mA
  • 공급 전압 12 ~ 28 Vdc
  • 무게 150 g

Supported Applications

The EA2-TX Series is the Easidew 2-wire dew-point transmitter from Michell Instruments, a compact loop-powered instrument for measuring moisture content in gases. Delivering its reading as a standard current signal, it installs directly into a process line or sample block and reports dryness continuously to a controller, PLC, or monitoring system.

It is well suited to natural gas, hydrogen, nitrogen, air, and inert gas systems, and to compressed-gas drying where product quality depends on low moisture. A choice of process connections and electrical connectors makes the EA2-TX straightforward to fit into new or existing sampling arrangements for reliable, long-term dew-point monitoring.

Operating Conditions & Performance

The transmitter measures dew point over -110 to +20°C (-166 to +68°F), with a companion range of -100 to +20°C (-148 to +68°F), resolving readings to 0.01 °C. It holds an accuracy of ±0.5 °C / ±0.9 °F with a repeatability of ±0.2 °C, and provides a typical T90 response of less than 10 seconds.

Output is a 4–20 mA loop signal with RS485 / Modbus RTU communications, powered from 10–30 VDC into a load of up to 500 Ω at 24 VDC, terminated through a DIN 43650 or M12 connector. The sensor withstands pressures up to 45 MPa (450 barg / 6500 psig), and its wetted parts use 316L stainless steel with an HMWPE guard.

The EA2-TX carries an IP67 enclosure and operates over a process range of -100 °C to +100 °C, an ambient range of -40 °C to +85 °C, and storage to -40 °C to +85 °C. The probe measures 12 mm in diameter with a 25 mm insertion length, a 50 mm stem, and a 100 mm overall length. Approvals include ATEX, IECEx, UL, CSA, and NEC.

Configuration Options

The EA2-TX is ordered as a configured transmitter, with a simplified alphanumeric code that fixes each feature to the application. The configurable axes are:

  • Range — a -100 to +20°C or -110 to +20°C dew-point range, or a non-standard configured range in °C, °F, or ppmV.
  • Protection — a standard HDPE guard against fine particulates, or a stainless-steel sintered guard.
  • Oxygen cleaning — standard, or cleaned for oxygen service, which is offered only with the stainless-steel sintered guard.

The choices that most change the delivered instrument are the guard type and oxygen-cleaning selection, which together govern particulate protection and suitability for oxygen-enriched media, while the range option sets the span over which the transmitter is scaled.

Key Product Differences

Ordering follows the parent code and its three feature positions, EA2-TX - <Range> - <Protection> - <Oxygen Cleaning>. The lineup spans the letter combinations from EA2-TX-AAA through EA2-TX-BBB, for example:

  • EA2-TX-ABB — Easidew 2-wire transmitter with the -100 to +20°C range, a stainless-steel sintered guard, and oxygen-cleaned wetted parts.
  • EA2-TX-RAA — non-standard range built to customer specification with an HDPE guard and no oxygen cleaning; the range is specified at time of order.

Under the previous ordering system the same choices were written out longhand, for example EA2-TX+(-100/+20C)+HD for the base transmitter with the -100 to +20°C range and an HDPE guard. Across every configuration the core sensing platform is unchanged — the model number simply records the chosen range, guard, and oxygen-cleaning options.

ko-KR
ko_KR
설정 저장