検索へジャンプ メインコンテンツへジャンプ ナビゲーションへジャンプ

日本 +81 3 6822 0370 | 新しいウェブサイトへようこそ。問題やバグを見つけましたか?こちらからご報告ください

におられるようです。地域限定のオファーやサポートをご希望の場合は、下のリンクをクリックして、お住まいの地域のサイトにアクセスしてください。

Series-DHII

Digihelic® 差圧コントローラー、NEMA 4、2リレー、Modbus

Digihelic® 차압 컨트롤러, NEMA 4, 2 릴레이, Modbus
  • NEMA 4ハウジングにより、水のある屋外または屋内のさまざまな用途に対応
  • 大型バックライトLCDディスプレイにより、遠くからのローカル読み取りが可能
  • 着脱可能な端子台が配線の手間を軽減し、設置時間を短縮
Series-DHII
販売元 1,853,561 원
Digihelic® 차압 컨트롤러, NEMA 4, 2 릴레이, Modbus Series-DHII Series-DHII
loading all models
製品の概要
  • 精度の詳細 ±0.5%(77°F(25°C)時)、ヒステリシスおよび再現性を含む(1時間のウォームアップ後)
  • ボーレート 9600
  • 補償温度、最大 140 °F
  • 補償温度、最小 32 °F
  • データインターフェース Modbus RTU, RS485
  • 表示に関する注意事項 4桁バックライト付きLCD、高さ0.6インチ。設定値およびアラーム状態用LEDインジケーター
  • 表示タイプ LCD
  • 電気接続 1/2インチ NPT メスコンジット(ネジ付き端子台付き)
  • エンクロージャーの定格 IP66, NEMA タイプ 4X
  • 材料 アルミニウム、ガラス
  • 材料、湿潤 メーカーにお問い合わせください
  • 対応媒体 クリーンな乾燥空気 / 不活性ガス, HVAC / 室内空気, 不活性/非反応性ガス
  • 取付方向 水平
  • 桁数 4
  • 動作温度(最高) 140 °F
  • 動作温度(最低) 32 °F
  • 出力詳細 4-20 mA DC 最大900 Ωまで
  • 出力信号 電流
  • 消費電力 7 VA、低電力: 130 mA
  • 圧力タイプ 差分
  • プロセス接続サイズ 1/8インチ
  • プロセス接続タイプ NPT メス
  • 応答時間 250 ms
  • 応答時間の注記 250 ms(ダンピング設定1)
  • シリーズID Series-DHII
  • セットポイント調整 メニュー設定可能
  • 安定性 <± 1%/年
  • 電源注記 高電圧電源 = 100-240 Vac、50-400 Hz または 132-240 Vdc、低電圧電源 = 24 Vdc ± 20%。
  • 電源タイプ AC / DC
  • 供給電圧 100から240 Vac、132から240 Vdc
  • スイッチノート 240 Vac抵抗負荷時 8 A
  • スイッチ定格 8 A @ 240 Vac
  • スイッチタイプ (2) SPDT
  • 熱効果 0.020%/°F(77°F時)
  • 重量 2.62 lb
  • ゼロ点設定調整範囲 メニューからアクセス可能

Supported Applications

The Dwyer Series DHII Digihelic® II is a differential pressure controller designed for measuring air and non-combustible, compatible gases. The unit features a 4-digit backlit LCD display and provides control via two SPDT relays alongside an analog output.

  • Differential pressure monitoring in HVAC systems
  • Process value retransmission via Modbus RTU RS485 serial communication

Operating Conditions & Performance

The Series DHII operates within ambient and process temperature ranges of 32 to 140°F (0 to 60°C). Accuracy is specified as ±0.5% at 77°F (25°C) including hysteresis and repeatability after a 1-hour warm-up period. The response time is 250 ms with dampening set to 1.

  • Enclosure Rating: NEMA 4 (IP66)
  • Housing Material: Aluminum, glass
  • Burst Pressure Limits by Range: • Ranges ≤ 2.5 in. w.c.: 2 psi • 5" to 100": 5 psi or 9 psi depending on range (see specific model)

Measurement Envelope

The series supports multiple differential pressure ranges, including unidirectional and bidirectional spans:

  • DH-002: 0 - 0.1 INWC
  • DH-004: 0 - 1.0 INWC
  • DH-006 to DH-010: Ranges from 5" to 100" INWC (unidirectional)
  • DH-012 to DH-017: Bidirectional ranges including +/- 0.25, +/- 0.5, +/- 1.0, +/- 2.5, +/- 5.0, and +/- 10 INWC

Electrical & Output Specifications

The controller accepts power from 100 to 240 VAC (50 to 400 Hz), 132 to 240 VDC, or 24 VDC ±20%. It provides a 4-20 mA DC output into a maximum load resistance of 900 OHMS. Two SPDT relays are available for control actions.

Configuration Options

The Series DHII is configurable across several parameters to meet specific installation needs:

  • Housing & Mounting: Vertical mounting with 1/8 female NPT process connections. Optional A-438 Bracket Mounting Diagram available.
  • Electrical Connections: Euro type removable terminal blocks with watertight conduit fittings for 1/2" watertight conduit.
  • Communication: Modbus RTU RS485 at 9600 Baud, 8 data bits, no parity, 1 stop bit. Factory default address is 50 (32h).
  • Display & Control Logic: Supports Single Set Point, Two Set Point, or Set Point/Alarm control types. Display units configurable for INWC, FTWC, MMWC, CMWC, PSI, INHG, MMHG, MBAR, PA, KPA, HPA, OZIN, SFPM, M/S, SCFM, and M^3H.
  • Advanced Functions: Includes peak/valley tracking, alarm delay (0-100 seconds), security levels 1–4, and maintenance mode for set point adjustments without affecting the process display.

Key Product Differences

Variants within the Series DHII differ primarily by their measurement range. The series includes models with unidirectional ranges (e.g., DH-001 through DH-010) and bidirectional ranges centered at zero (e.g., DH-011 through DH-017). All variants share the same NEMA 4 enclosure, dual relay output structure, Modbus RTU communication protocol, and power supply options. Specific burst pressure ratings vary by range; for example, models with ranges ≤ 2.5 in. w.c. have a limit of 2 psi, while higher ranges such as 100" INWC support up to 9 psi.

アクセサリー

accessories

Static pressure tip, for 1/4" metal tubing connection.
¥2,860 / 各
0 facet.availability.sku_availability
Static pressure tip, for 3/16" and 1/8" ID plastic or rubber tubing.
¥2,768 / 各
0 facet.availability.sku_availability

installation hardware

Surface mounting bracket
¥4,777 / 各
0 facet.availability.sku_availability

signal conditioners

¥23,065 / 各
0 facet.availability.sku_availability
DHII-001002004006007030008009010011012013014015016017-COO-NIST
DHII 범위
DHII 옵션
ja-JP
ko_KR
設定を保存する