검색으로 이동 메인 콘텐츠로 이동 탐색으로 이동

한국 1588-8983 | 새로운 웹사이트에 오신 것을 환영합니다. 문제나 버그를 발견하셨나요? 여기에 보고해주세요

현재 에 계신 것을 확인했습니다. 아래 링크를 클릭하여 지역 사이트를 방문하시면, 지역별 특가 혜택과 지원 서비스를 받으실 수 있습니다.

LDI-G19

컴팩트 LVIT 선형 위치 센서

재고가 있는 모델
  • 접촉 없는 작동으로 떨림 또는 사이클링에 의한 마모 방지
  • 우수한 스트로크 대 길이 비율
  • 견고한 19 mm (0.75인치) 직경 산업용 등급 스테인리스강(예: 304/316 SS)
LDI-G19
시작 1,972,505 원
재고가 있는 모델
컴팩트 LVIT 선형 위치 센서 LDI-G19 LDI-G19
loading all models
제품 개요
  • 추가 기능 1 스프링 장착
  • 대역폭 300 Hz (-3 dB)
  • 외함 등급 IP67
  • 하우징 재질 스테인리스 스틸
  • 토크 장착 0.41 kgf/cm
  • 작동 온도, 최대 85 °C
  • 최소 작동 온도 -20 °C
  • 상대 습도 95% RH, 비응축
  • 해상도 FS의 0.025%
  • 시리즈 ID LDI-G19
  • 충격 1000 g, 11 ms
  • 온도 계수 0.015% FS/°C
  • 진동 5~20 Hz, 0.5" p-p; 20~2000 Hz, 4.2 g p-p

Supported Applications

The Omega LDI Series Compact, LVIT Linear Position Sensors are designed for linear position measurement. The series identity is defined by its function as a displacement transducer within the Automation & Control category.

Operating Conditions & Performance

These sensors operate on an excitation voltage of 12-30 V DC, with a minimum requirement of 18 V DC for the 4-20 mA current output. The series provides analog outputs in two configurations: 0-10 VDC or 4-20 mA. A critical operational constraint is that the 4-20 mA DC output utilizes 3-wire sourcing and must not be connected to a 2-wire loop-powered system.

Field programmability allows calibration ranges to be set within specific limits: 0-20% around zero or 80-100% around full range. The default setting for the output is 0-10 VDC and 4-20 mA. Load resistance options are available at 250 Ohms or 500 Ohms.

Electrical Connections

The series supports two electrical connection methods: a 4-conductor cable or a PTO2-10 6-pin connector. Pin assignments and conductor colors are defined as follows:

  • Red (Pin E): + Power Input, 12-30 V DC (min. 18 V DC for 4 - 20 mA current output)
  • Black (Pin D): Common Ground
  • Green (Pin A): Analog DC Output: 0 -10 V or 4 - 20 mA
  • White (Pin B): Field Programmability (cal)

Safety and Compliance

The series carries CE approval. A specific warning states that these products are not designed for use in, and should not be used for, human applications.

Configuration Options

The LDI-G19 series is offered with multiple stroke lengths indicated by the model number suffixes (e.g., 006, 013, 025, 050, 075, 100). Output signal types are configurable between voltage and current modes. The sensors feature field programmability for calibration adjustments.

Key Product Differences

Variants within the LDI-G19 series differ primarily by stroke length and output configuration codes (A210S vs A220S). All variants share the same electrical connection options, power requirements, and field programmability ranges as documented in the instruction sheet.

ko-KR
ko_KR
설정 저장