한국 1588-8983 | 새로운 웹사이트에 오신 것을 환영합니다. 문제나 버그를 발견하셨나요? 여기에 보고해주세요
LC8250
2.5인치 OD 관통형 압축 하중 셀
- 저프로파일
- 5점 NIST 추적 교정 및
59 kOhm 션트 교정 데이터 - 전 산업용 등급 스테인리스강(예: 304/316 SS)
제품 개요
- 5점 보정 0%, 50%, 100%, 50%, 0%
- 케이블 길이 5 ft
- 보정 옵션 5 포인트 NIST
- 전기 연결 케이블
- 전기 출력 2 mV/V
- 힘 유형 압축
- 풀 스케일 편차 0.003 in
- 높이 1 in
- 입력 저항 360 Ω 최소
- 선형성 ± 0.5%
- 로드셀 타입 통과 구멍
- 재료 17-4 PH 스테인리스 스틸
- 작동 온도, 최대 121 °C
- 최소 작동 온도 -54 °C
- 외경 2.5 in
- 출력 저항 350 ± 5 Ω
- 과부하, 최대 300% FS
- 공정 온도, 최대 71 °C
- 최소 공정 온도 16 °C
- 반복성 ± 0.1%
- 안전 과부하 150% FS
- 시리즈 ID LC8250
- 공급 전력 참고 10 Vdc, 최대 15 Vdc
- 공급 전압 10 Vdc
- 열적 스팬 효과 ± 0.018% rdg/°C
- 열 영점 효과 ± 0.009% FSO/°C
- 배선/커넥터 테이블 녹색: (+) 출력; 흰색: (-) 출력; 검정: (-) 입력; 빨강: (+) 입력
- 영점/밸런스 오차 ± 2%
Supported Applications
The Omega LC8250 Series consists of compact, low-profile, all stainless steel donut load cells designed for through-hole applications. These compression load cells are suitable for measuring compressive forces in clamping and bolt loading scenarios.
Operating Conditions & Performance
The series operates within an ambient temperature range of -54 to 121°C (-65 to 250°F). Electrical performance is defined by a nominal output signal of 2 mV/V and requires an excitation voltage of 10 Vdc (15V maximum). The load cells feature an accuracy class of ±0.5% FSO and repeatability of ±0.1% FSO.
Physical dimensions are fixed across the series with a height of 25 mm (1.0") and an outer diameter of 64 mm (2.50"). The units include a 1.5 m (5') 4-conductor shielded cable for electrical connection.
Measurement Ranges
The LC8250 series supports the following compression capacities:
- 0-1,000 lb to 0-75,000 lb (increments of 1K through 7.5K)
- 0-100,000 lb
- Metric equivalents range from 455 kgf to 45,372 kgf as listed in the specification tables.
Configuration Options
The series is configurable by inside diameter (ID) and capacity. The model number format follows LC8250-[ID CODE]-[CAPACITY]K, where the ID code corresponds to specific hole sizes ranging from 0.250" to 1.50".
Inside Diameter Options
The following inside diameters are available depending on capacity selection:
- 0.250", 0.375", 0.500", 0.625", 0.750" (ID Codes: 250, 375, 500, 625, 750)
- 0.875", 0.938", 1.00", 1.13", 1.25" (ID Codes: 875, 938, 1.00, 1.13, 1.25)
- 1.38", 1.50" (ID Codes: 1.38, 1.50)
Cable and Wiring
The standard electrical connection is a 4-conductor shielded cable with the following wire color code:
- Green (GN): +Output
- White (WT): -Output
- Black (BK): -Input
- Red (RD): +Input
Certifications and Calibration
The load cells are supplied with a 5-point NIST-traceable calibration. The series holds RoHS compliance.
Key Product Differences
Variants within the LC8250 family differ primarily by their inside diameter and rated capacity, allowing integration into existing through-hole structures of varying sizes. For capacities greater than 50,000 lb, top and bottom loading surfaces are located through the center hub.
While standard configurations use inch-based ID codes, metric configurations are available upon consultation with engineering. Compatible meters for these load cells include models DP41-S, DP25B-S, and DPIS.
PDF 및 매뉴얼