検索へジャンプ メインコンテンツへジャンプ ナビゲーションへジャンプ

日本 +81 3 6822 0370 | 新しいウェブサイトへようこそ。問題やバグを見つけましたか?こちらからご報告ください

におられるようです。地域限定のオファーやサポートをご希望の場合は、下のリンクをクリックして、お住まいの地域のサイトにアクセスしてください。

SF82-TX

SF82 トランスミッター 2線式

  • 露点またはppmV水分含有量出力
  • 精度 ±2 °C(±3.6 °F)露点
  • MiniDIN 43650 C、M12 電気コネクタ
SF82-TX
販売元 ¥ 286,236
SF82 トランスミッター 2線式 SF82-TX SF82-TX
loading all models
製品の概要
  • 応用例 空気, エアドライヤー, クリーンルーム, コンプレッサー制御, ガス, 研究所, 研究所と科学部門, 材料と表面, 医療機器, 特殊装備
  • 補償温度、最大 50 °C
  • 補償温度、最小 -20 °C
  • コンプライアンスに関する注意事項 IEC61010-1、UL61010-1およびCAN/CSA C22.2 No. 61010 EN61373 鉄道車両 EN50121-3-2: 2016 鉄道EMC/RFI
  • 寸法に関する注意事項 L = 156 mm x ø45 mm(6.14インチ x ø1.77インチ)(コネクタケーブル付き)
  • 電気出力 0~20 mA
  • 流量に関する注記 1...5 Nl/min 標準サンプリングブロックに取り付け; 0...10 m/sec 直接挿入
  • 高さ 133 mm
  • ハウジング材質 316ステンレス鋼
  • 長さ 45 mm
  • 荷重抵抗 最大250 Ω @ 12 V(500 Ω @ 24 V)
  • 動作圧力(最大) 10 MPa
  • 動作温度(最高) 60 °C
  • 動作温度(最低) -20 °C
  • 耐圧力 最大 6526.7 psi
  • センサーフィルター 10 µm標準HMWPEガード
  • シリーズID SF82-TX
  • 最大保管温度 60 °C
  • 保管温度(最低) -40 °C
  • 供給電流 23 mA

Supported Applications

The Michell SF82 Transmitter is a rugged, two-wire dew-point transmitter designed for the continuous measurement of moisture content in gases. The series is engineered specifically for industrial dryer applications requiring precise humidity monitoring.

Suitable media include non-corrosive gases, clean dry air, and inert gases. The device measures dew point directly to determine gas moisture levels within specified operating envelopes.

Operating Conditions & Performance

The SF82 series operates across a measurement range of -60 to +20 °C (-76 to +68 °F). Accuracy is rated at ±0.5 °C (±0.9 °F) with repeatability of ±0.2 °C and resolution of 0.1 °C. The response time (T90) is less than 10 seconds.

Process and ambient operating temperatures range from -40 to +85 °C, matching the storage temperature limits. The transmitter supports a pressure rating of 0 to 10 bar with a burst pressure limit of 100 bar. It maintains an IP67 enclosure rating and withstands vibration up to 10–500 Hz at 1.5 mm amplitude and shock loads of 100 g for 11 ms.

Electrical requirements include a power supply of 12–30 VDC with a maximum load resistance of 500 Ω. The device carries CE and FCC Part 15 approvals.

Configuration Options

The SF82-TX series offers configurable process connections, measurement ranges, electrical interfaces, and protective options to accommodate specific installation requirements.

  • Process Connections: Available in G1/2" BSPP, 3/4" - 16 UNF, or 5/8" 18 UNF threads.
  • Measurement Ranges: Standard scaled ranges include -60/+60°Cdp, -50/+50°Cdp, -50/+30°Cdp, -80/+20°Cdp, and -20/+50°Cdp. Non-standard measurement ranges are available upon request.
  • Output Signals: Configurable for 4–20 mA analog output or RS485 / Modbus RTU digital communication (enabled via M12 connector selection).
  • Electrical Connectors: Options include MiniDIN 43650 or M12 5 Pin connectors. Note that the mating connector is not supplied and must be ordered separately.
  • Protection: Standard configuration includes an HMWPE guard for protection against fine particulates (<10 μm).

The series supports various accessories including sample blocks, sampling kits (atmospheric or high pressure), PTFE tubing, and replacement parts such as sensor elements and connector assemblies.

Key Product Differences

Variants within the SF82-TX family are distinguished by their process connection type, selected measurement range, electrical interface, and protective guard configuration. The model number structure follows the format SF82 - TX - Type - Range - Protection - Electrical Connector.

  • Process connections vary between G1/2" BSP (Type A), 3/4" UNF (Type B), and 5/8" UNF (Type C).
  • Measurement ranges are selected via codes corresponding to specific scaled outputs, such as -60/+60°Cdp or non-standard ppmV conversions.
  • The electrical connector choice determines signal capability: MiniDIN 43650 supports standard analog output, while the M12 5 Pin option enables both 4–20 mA and Modbus RTU over RS485 outputs.
ja-JP
ja_JP
設定を保存する