検索へジャンプ メインコンテンツへジャンプ ナビゲーションへジャンプ

日本 +81 3 6822 0370 | 新しいウェブサイトへようこそ。問題やバグを見つけましたか?こちらからご報告ください

におられるようです。地域限定のオファーやサポートをご希望の場合は、下のリンクをクリックして、お住まいの地域のサイトにアクセスしてください。

Series-3000MR-3000MRS

Photohelic® スイッチ/ゲージ、差圧、最大25 psig、コンパクト

  • スイッチ操作によるゲージ表示への影響なし。停電時でも圧力を読み続けることが可能
  • ゲージ外部でのゼロ点およびレンジ調整により、通常のメンテナンス時に分解不要
  • ソリッドステート設計により、高サイクル率のアプリケーションでも劣化なくスイッチング可能
Series-3000MR-3000MRS
販売元 ¥ 142,534
Photohelic® スイッチ/ゲージ、差圧、最大25 psig、コンパクト Series-3000MR-3000MRS Series-3000MR-3000MRS
loading all models
製品の概要
  • 精度の詳細 FSの±2%(3000-0はFSの±3%、3000-00はFSの±4%)。
  • ダイヤルの深さ 3.125 in
  • ダイヤル直径 4インチ
  • ダイヤル外径 5 in
  • 電気接続 ケーブル
  • 材料、湿潤 メーカーにお問い合わせください
  • 対応媒体 クリーンな乾燥空気 / 不活性ガス, HVAC / 室内空気, 不活性/非反応性ガス
  • 取付方向 垂直ダイアフラム
  • 動作温度(最高) 120 °F
  • 動作温度(最低) 20 °F
  • 圧力(最小) 0 inH₂O
  • 圧力タイプ 差分
  • プロセス接続に関する注記 1/8˝ メス NPT(側面および背面に重複)
  • プロセス接続サイズ 1/8インチ
  • プロセス接続タイプ NPT メス
  • 耐圧力 -20 inHg ~ 25 psi
  • シリーズID Series-3000MR-3000MRS
  • セットポイント調整 調整可能なノブ
  • 電源注記 24 Vdc、±10% 調整済み
  • 電源タイプ DC
  • 供給電圧 24 Vdc
  • 重量 1.8 lb

Supported Applications

The Dwyer Series 3000MR and 3000MRS Photohelic® Switch/Gages combine a differential pressure gage with low/high set-points in a compact size. These units are designed for use with air and non-combustible, compatible gases, as well as non-corrosive gases. Documented applications include pneumatic conveying systems, air conditioning systems, and clean rooms.

Operating Conditions & Performance

The series operates within a process temperature range of 20 to 120°F (-6.67 to 48.9°C). Standard pressure ratings cover -20" Hg to 25 psig (-0.677 bar to 1.72 bar), with optional constructions available for higher pressures: the MP option increases the maximum rated pressure to 35 psig (2.41 bar) and the HP option to 80 psig (5.52 bar). Gage accuracy is specified as ±2% of full scale, with specific model variations noted at ±3% or ±4% of full scale depending on the range.

Process connections are provided via duplicated 1/8" female NPT ports located on the side and back. The unit weighs 1.8 lb (816 g) and features a 4" (101.6 mm) dial face with an overall height of 3-1/8" (79.38 mm). Mounting orientation requires the diaphragm to be in a vertical position; other orientations require consultation with the factory.

Configuration Options

The series offers extensive configuration options across measurement ranges, output types, and environmental protections:

  • Measurement Ranges: Available scales include 0-0.25 in w.c., 0-100 in w.c., 0-60 Pascals to 0-4.0 kPa, and various mm w.c./cm w.c. ranges.
  • Output Signals: Models are available with either electromechanical relays (3000MR) or solid-state technology (3000MRS). The 3000MR models feature Form C relay contacts rated for resistive loads of 1.0A @ 30 VDC, 0.3A @ 110 VDC, or 0.5A @ 125 VAC with gold over clad silver contacts suitable for dry circuits.
  • Power Requirements: All models require a regulated 24 VDC power supply (±10%). The solid-state relay switching voltage is rated at 20-280 VAC (47 - 63 Hz).
  • Housing and Bezel Options: A standard bezel is available, or the optional -SS suffix provides a 304 brushed stainless steel bezel that maintains backward compatibility with standard Magnehelic® gage installation diameters.
  • Special Service Options: Configurations include the -LT option for use under 20°F (-6.7°C), the -WP weatherproof housing, and tamper-proof knobs requiring a spanner key (-TAMP).

Cable assemblies are standard at 18" (45 cm) or 18" (46 cm) depending on the model variant, with optional lengths available up to 100' (30.5 m). Wetted materials should be confirmed by consulting the factory.

Key Product Differences

The primary distinction between models lies in the switching technology and contact configuration:

  • Series 3000MR (Electromechanical): Employs versatile electromechanical relays with gold over clad silver contacts. Each set point utilizes a Form C relay (SPDT). These units are noted for suitability in dry circuits.
  • Series 3000MRS (Solid-State): Utilizes solid-state technology, providing SPST N.O. (Single Pole Single Throw, Normally Open) relays. This design supports high cycle rate applications without degradation and allows the gage reading to remain accurate even if power is interrupted.

Both series share identical physical dimensions for standard bezels and offer adjustable set points via external knobs on the face of the unit. The -SS stainless steel bezel option alters the overall height to 2-21/32" (67.5 mm) while maintaining a 4-3/4" (120.7 mm) O.D.

アクセサリー

accessories

R/C snubber (recommended for inductive loads like a solenoid or contactor)
¥5,479 / 各
0 在庫あり

installation hardware

Flat aluminum bracket for flush mounting (for Series A3000 Photohelic®, Series 4000 Capsuhelic®, Series 605, and Series 3000MR)
¥8,009 / 各
0 在庫あり
Flush mount bracket used with: Photohelic® 3000MR/MRS, Capsuhelic®, 631B Transmitter. Bracket is then surface mounted. Steel with gray hammertone epoxy finish.
¥9,658 / 各
0 在庫あり
300033003001300230033004300530063008301030153020302530303040305030603080310031503250330133023304331033203330334033603380320132023203320432053210321532203230MRMRS-00N-00-0-00AV-0AV-5HG-10HG-15HG-20HG-25HG-30HG-40HG-50HG-60HG-6MM-10MM-20MM-25MM-30MM-50MM-80MM-100MM-150MM-250MM-300MM-500MM-1CM-2CM-5CM-8CM-10CM-15CM-20CM-25CM-30CM-40CM-50CM-80CM-100CM-150CM-200CM-250CM-300CM-500CM-60PA-125PA-200PA-250PA-500PA-750PA-1KPA-1.5KPA-2KPA-3KPA-4KPA-5KPA-8KPA-10KPA-15KPA-20KPA-25KPA-30KPA-40KPA-50KPA-15MBAR-20MBAR-100MBAR-500MBAR-0-20MM-30MM-40MM-4CM-10CM-20CM-30CM-120PA-250PA-500PA-1000PA-1KPA-2KPA-3KPA-24VAC-AT-BUNA-COO-DEED-EDED-EDDE-EXPL-G-HC-HP-LT-M-MP-NIST-R-CBL3-CBL5-CBL10-CBL15-CBL20-CBL25-CBL30-CBL40-CBL50-CBL60-CBL70-CBL80-CBL90-CBL100-SF
ja-JP
ja_JP
設定を保存する