検索へジャンプ メインコンテンツへジャンプ ナビゲーションへジャンプ

日本 +81 3 6822 0370 | 新しいウェブサイトへようこそ。問題やバグを見つけましたか?こちらからご報告ください

におられるようです。地域限定のオファーやサポートをご希望の場合は、下のリンクをクリックして、お住まいの地域のサイトにアクセスしてください。

Series-V10

1/2~2インチ配管用ミニ流量スイッチ、真鍮またはステンレス製ボディ

  • 堅牢な磁気作動スイッチ設計と密閉型リードスイッチによる優れた性能
  • 電気接続を変更せずに、現場で簡単に通常開(NO)または通常閉(NC)に切り替え可能な柔軟な用途対応
  • ユニットを取り外すことなく電気部品を簡単に交換できるため、メンテナンス時間とコストを削減し、プロセスの停止を回避
  • 真鍮またはダクタイル鉄製レデュースドティー用に校正された取り外し可能なテンプレート付きのフルサイズで現場調整可能なステンレス製ベーンにより、鍛造鋼製のストレートティー/ブッシング組み合わせに対応し、用途ニーズを解決
Series-V10
販売元 ¥ 50,232
1/2~2インチ配管用ミニ流量スイッチ、真鍮またはステンレス製ボディ Series-V10 Series-V10
loading all models
製品の概要
  • 電気接続 ケーブル
  • エンクロージャーの定格 IP66, NEMA タイプ 4X, 耐候形
  • 材料 ナイロン
  • 対応媒体 クリーンな乾燥空気 / 不活性ガス, プロセス水/冷却水, 適合する液体, 不活性/非反応性ガス, 油/潤滑油, 有機溶剤
  • 取付方向 なし
  • 動作温度(最高) 200 °F
  • パイプサイズ、最大 2 in
  • パイプサイズ、最小 0.5 in
  • 圧力タイプ ゲージ
  • プロセス接続サイズ 1/2インチ
  • プロセス接続タイプ NPT オス
  • シリーズID Series-V10
  • セットポイント調整 ベーンの調整
  • スイッチ定格 0.5 A @ 120 Vac、1.5 A @ 24 Vdc、0.001 A @ 200 Vdc
  • スイッチレーティングの注意 SPST密封リードスイッチ。現場で常時開または常時閉に調整可能、定格:0.5 A @ 120 Vac;1.5 A @ 24 Vdc抵抗負荷;0.001 A @ 200 Vdc抵抗負荷。
  • スイッチタイプ SPST リード
  • 重量 0.16 kg
  • 線径 18 AWG

Supported Applications

The Dwyer Series V10 Flotect® Mini-Size Flow Switch is designed to monitor the presence or absence of flow in compatible gases or liquids. This hermetically sealed reed switch sensor features a vane actuated mechanism suitable for installation in horizontal pipe runs ranging from 1/2" to 2" diameter.

Operating Conditions & Performance

The series operates with process temperatures up to 200°F (93°C). Pressure ratings depend on the body material: brass bodies are rated for 1000 psig (69 bar), while 303 SS bodies support 2000 psig (138 bar). The enclosure is weatherproof, meeting NEMA 4X (IP66) standards.

Flow actuation and deactuation rates vary by pipe size and trim configuration. For cold water applications in a horizontal run, approximate flow ranges span from 2.6/2.3 GPM to 9.5/9.1 GPM for Normally Open (N.O.) configurations across the documented trims. Air flow actuation/deactuation rates range approximately from 10.3/8.8 SCFM to 50.2/48.4 SCFM for N.O. settings, with specific values dependent on pipe diameter and trim selection.

Configuration Options

The Series V10 offers configurable options across body materials, process connections, and switch logic:

  • Body Materials: Brass or 303 SS. Wetted parts include a 301 SS vane, pin, spring (available in 302 SS and 316 SS), and Ceramic 8 magnet.
  • Process Connections: Available with 1/2" male NPT or 1/2" male BSPT threads.
  • Switch Configuration: SPST hermetically sealed reed switch, field adjustable for Normally Open (N.O.) or Normally Closed (N.C.).
  • Electrical Connections: Includes 18 AWG lead wires, 19" (483 mm) long with PVC jacket rated to 221°F (105°C).
  • Approvals: CE, CSA, and UR.

The switch enclosure is constructed of Nylon. The unit weighs 5.5 oz (0.16 kg). While the switch can be installed in any position, documented actuation/deactuation flow rates are based on horizontal pipe runs and represent nominal values.

Key Product Differences

The series is identified by specific model codes reflecting body material and connection type:

  • V10: Brass body with NPT connection.
  • V10SS: 303 SS body with NPT connection.
  • V10-BSP: Brass body with BSPT connection.
  • V10SS-BSP: 303 SS body with BSPT connection.

All models support field adjustment between normally open and normally closed switch configurations. The vane is trimmable to adjust the set point. Note that mechanical shock or vibration can cause permanent damage to the reed switch, and inductive, capacitive, or lamp loads may require protection circuit solutions.

V10V10SS-BSPT-ST
ハウジング材質
オプション
"
ja-JP
ja_JP
設定を保存する