検索へジャンプ メインコンテンツへジャンプ ナビゲーションへジャンプ

日本 +81 3 6822 0370 | 新しいウェブサイトへようこそ。問題やバグを見つけましたか?こちらからご報告ください

におられるようです。地域限定のオファーやサポートをご希望の場合は、下のリンクをクリックして、お住まいの地域のサイトにアクセスしてください。

Series-HFT

流量トランスミッター、4-20 mA/0-5 Vdc、廃水およびプロセス制御用

  • アナログ出力を提供し、アプリケーションの流量を監視し、積分直接読み取りスケールにより流量の局所表示を提供
  • 入口および出口の直管配管が不要で、水平、垂直、または逆さまに取り付け可能なため、アプリケーションの多様性を向上
  • 頑丈な鋳造アルミニウム構造とNEMA 4X(IP65)エンクロージャにより、屋外または過酷な環境での設置が可能
Series-HFT
販売元 ¥ 322,974
流量トランスミッター、4-20 mA/0-5 Vdc、廃水およびプロセス制御用 Series-HFT Series-HFT
loading all models
製品の概要
  • 精度 ± 2 %
  • 精度の詳細 ± 2% FS
  • エンクロージャーの定格 IP66, NEMA タイプ 4X
  • 対応媒体 クリーンな乾燥空気 / 不活性ガス, プロセス水/冷却水, 適合する液体, 不活性/非反応性ガス, 油/潤滑油, 有機溶剤
  • 動作温度(最高) 170 °F
  • 出力詳細 4~20 mA、0~5 V、1~5 V
  • 出力信号 電流、電圧
  • 圧力タイプ ゲージ
  • プロセス接続タイプ NPT メス
  • 繰り返し精度 ± 1%
  • 応答時間 <100 ms
  • シリーズID Series-HFT
  • 電源タイプ DC
  • 供給電圧 12から35Vdc
  • 粘度範囲 500 SSU

Supported Applications

The Dwyer Series HFT In-Line Flow Transmitter provides continuous monitoring of flow rate levels via a direct reading in-line flowmeter with electronics to provide proportional analog outputs. These transmitters are typically used to transmit a signal proportional to flow rate to a process control computer, a PLC, a recorder, or a panel-mount display. The series serves as the primary input device to record flow rates through hydraulic and pneumatic systems.

Operating Conditions & Performance

The Series HFT is designed for service with compatible gases or liquids up to 500 SSU viscosity. Process temperature limits are rated at 170°F (76°C). The transmitter delivers an accuracy of ±2% FS and repeatability of ±1% of full scale, with a response time of less than 100 msec.

Pressure ratings vary by body material: Aluminum bodies support up to 600 psig (41 bar), Brass bodies up to 3500 psig (240 bar), and 304 SS bodies up to 6000 psig (413 bar). The unit operates on a power supply of 12-35 VDC. For the 4-20 mA output, load resistance is defined as Rmax = 50(Vs - 12), and the input impedance of the receiving device must not be lower than 100 Ω to avoid non-linearities.

Configuration Options

The series offers a range of process connections, body materials, and output configurations tailored to specific flow ranges:

  • Process Connections: Available in 1/4", 1/2", 3/4", 1", and 1-1/2" female NPT.
  • Body Materials: Aluminum, brass, or 304 SS. Wetted materials include Buna-N or Fluoroelastomer seals; a PTFE coated Alnico magnet; and other internal parts in 304 SS.
  • Housing & Enclosure: Rugged cast aluminum housing with NEMA 4X (IP65) enclosure rating. Overall dimensions are 7-1/8" height, 4-1/2" width, and 2-15/16" depth.
  • Output Signals: The universal output circuit produces 4-20 mA, 0-5 VDC, or 1-5 VDC. A 1-5 VDC signal may be obtained from the 4-20 mA signal by placing a 249 Ω resistor in parallel with the receiver. Some configurations support a 0-2000 Hz square wave pulse output.
  • Electrical Connection: Utilizes a 4-pin DIN connector.

The series supports various flow ranges depending on media and model, including water flows from .2 to 50 GPM (1 to 190 LPM) and air/gas flows up to 23 SCFM or higher. Shipping weight varies by connection size: 3 lb (1.4 kg) for 1/4" to 1/2" models, 4.5 lb (2.0 kg) for 3/4" to 1" models, and 12 lb (5.4 kg) for 1-1/2" models.

Key Product Differences

Variants within the Series HFT are distinguished by connection size, body material, and specific flow range capabilities:

  • HFT-11xx Models (Aluminum): Feature 1/4" female NPT connections for air/gas ranges such as 2 to 12 SCFM or 4 to 23 SCFM.
  • HFT-2xxx Models (Brass): Offered in 1/2", 3/4", 1", and 1-1/2" female NPT sizes for water ranges spanning .5 to 50 GPM. These models support higher pressure ratings up to 3500 psig.
  • HFT-3xxx Models (304 SS): Available in 1/2" female NPT connections with low-flow water ranges such as .2 to 2 GPM or 1 to 10 GPM, supporting pressure ratings up to 6000 psig.

The series includes a green LED indicator for power status. Installation and cleaning instructions reference the Series HF In-Line Flow Monitor Bulletin F-55 for the basic flow monitor cartridge included with the unit.

ja-JP
ja_JP
設定を保存する