日本 +81 3 6822 0370 | 新しいウェブサイトへようこそ。問題やバグを見つけましたか?こちらからご報告ください
EA34-TX
Easidew 2線式露点トランスミッター
- 測定範囲 -110~+20 °Cdp
- 露点またはppm V 湿度含有量出力
- 精度 ±2 °Cdp
- 3/4” UNF プロセス接続
製品の概要
- アクセサリータイプ 5/8インチ18 UNFおよび3/4インチ 16 UNFプロセス接続用のフランジ
- 精度 ± 2 °C (± 3.6 °F)
- 精度の詳細 ±2 °C(±3.6 °F)露点*
- 応用例 空気, エアドライヤー, 化学精製所, クリーンルーム, クリーンウォーターと浄化溶液, コンプレッサー制御, フィルター監視, 流量測定, ガス, HVAC, 産業および製造業, 天然ガスコンプレッサー, 発電所とボイラー, 研究開発/エンジニアリング試験, 冷蔵, 冷蔵設備, 温度維持, 廃水の応用
- 校正に関する注記 トレーサブル13点校正証明書
- 補償温度、最大 50 °C
- 補償温度、最小 -20 °C
- コンプライアンスに関する注意事項 ATEX/UKCA: II 1 G Ex ia IIC T4 Ga (-20~+70 °C) IECEx: EX ia IIC T4 Ga (-20~+70 °C) TR CU @ 0Ex ia IICT4 Ga (-20~+70 °C) cQPSus: Class I, Division 1, Groups A, B, C & D, T4 Class I, Zone 0, AEx ia IIC T4 Gb, Ex ia IIC T4 Gb Tamb +70 °C
- 電気出力 0~20 mA
- エンクロージャーの定格 IP66, NEMA タイプ 4
- 工場出荷時設定 センサー故障:23 mA;アンダーレンジ露点:4 mA;オーバーレンジ露点:20 mA
- 流量に関する注記 標準サンプリングブロックに取り付けられた1~5 Nl/min;直接挿入式で0~10 m/sec
- ガルバニック絶縁 KFD2-CR-EX1.20200,KFD2-CR-EX1.30200,KFD0-CS-EX1.50P,KFD0-CS-EX2.50P,KFD2-STC4-EX1.H,MTL5041,MTL5040
- ハウジング材質 316ステンレス鋼
- 荷重抵抗 最大250 Ω @ 14 V(500 Ω @ 24 V)
- 測定タイプ 露点、湿度
- 動作圧力(最大) 52.5 MPa
- 動作温度(最高) 60 °C
- 動作温度(最低) -40 °C
- プロセス接続サイズ 3/4インチ
- プロセス接続タイプ UNF オス
- 繰り返し精度 0.5°C(0.9°F)露点
- 応答時間 5分でT95(乾燥から湿潤へ)
- シリーズID EA34-TX
- 最大保管温度 60 °C
- 保管温度(最低) -40 °C
- 供給電流 23 mA
- 供給電圧 12から28Vdc
- 重量 150 g
Supported Applications
The EA34-TX Series is the 3/4" UNF version of Michell Instruments' Easidew 2-wire dew-point transmitter, a compact loop-powered instrument for measuring moisture content in gases. Delivering its reading as a standard current signal, it threads directly into a process line or sample block and reports dryness continuously to a controller, PLC, or monitoring system.
It is well suited to natural gas, hydrogen, nitrogen, air, and inert gas systems, and to compressed-gas drying where product quality depends on low moisture. The 3/4" UNF thread makes the EA34-TX a straightforward fit for common sample-block and adapter fittings, giving reliable, long-term dew-point monitoring.
Operating Conditions & Performance
The transmitter measures dew point over -110 to +20°C (-166 to +68°F), with a companion range of -100 to +20°C (-148 to +68°F), resolving readings to 0.01 °C. It holds an accuracy of ±0.5 °C / ±0.9 °F with a repeatability of ±0.2 °C, and provides a typical T90 response of less than 10 seconds.
Output is a 4–20 mA loop signal with RS485 / Modbus RTU communications, powered from 10–30 VDC into a load of up to 500 Ω at 24 VDC, terminated through a DIN 43650 or M12 connector. The sensor withstands pressures up to 45 MPa (450 barg / 6500 psig), and its wetted parts use 316L stainless steel with an HMWPE guard.
The EA34-TX carries an IP67 enclosure and operates over a process range of -100 °C to +100 °C, an ambient range of -40 °C to +85 °C, and storage to -40 °C to +85 °C. The probe measures 12 mm in diameter with a 25 mm insertion length, a 50 mm stem, and a 100 mm overall length. Approvals include ATEX, IECEx, UL, CSA, and NEC.
Configuration Options
The EA34-TX is ordered as a configured transmitter on a fixed 3/4" UNF thread, with a letter-based code that fixes each remaining feature to the application. The configurable axes are:
- Range — a -100 to +20°C or -110 to +20°C dew-point range, or a non-standard configured range in °C, °F, or ppmV.
- Protection — a standard HDPE guard against fine particulates, or a stainless-steel sintered guard.
- Oxygen cleaning — standard, or cleaned for oxygen service, which is offered only with the stainless-steel sintered guard.
Because the process thread is fixed, the choices that change the delivered instrument are the guard type and oxygen-cleaning selection, which together govern particulate protection and suitability for oxygen-enriched media, while the range option sets the span over which the transmitter is scaled.
Key Product Differences
Ordering follows the parent code and its three feature positions, EA34-TX - <Range> - <Protection> - <Oxygen Cleaning>. The lineup spans the letter combinations from EA34-TX-AAA through EA34-TX-BBA, for example:
- EA34-TX-ABB — Easidew 2-wire transmitter with the -100 to +20°C range, a stainless-steel sintered guard, and oxygen-cleaned wetted parts.
- EA34-TX-RAA — non-standard range built to customer specification with an HDPE guard and no oxygen cleaning; the range is specified at time of order.
Under the previous ordering system the same choices were expressed as the base model plus feature codes for range, guard, and oxygen cleaning. Across every configuration the core sensing platform and 3/4" UNF thread stay the same — the model number simply records the chosen range, guard, and oxygen-cleaning options.