検索へジャンプ メインコンテンツへジャンプ ナビゲーションへジャンプ

日本 +81 3 6822 0370 | 新しいウェブサイトへようこそ。問題やバグを見つけましたか?こちらからご報告ください

におられるようです。地域限定のオファーやサポートをご希望の場合は、下のリンクをクリックして、お住まいの地域のサイトにアクセスしてください。

EA2-TX

Easidew 2線式露点トランスミッター

  • 測定範囲 -110 ~ +20 °Cdp
  • 露点またはppmV水分含有量出力
  • 精度 ±2 °Cdp
EA2-TX
販売元 ¥ 308,804
Easidew 2線式露点トランスミッター EA2-TX EA2-TX
loading all models
製品の概要
  • アクセサリータイプ 5/8インチ18 UNFおよび3/4インチ 16 UNFプロセス接続用のフランジ
  • 精度 ± 2 °C (± 3.6 °F)
  • 精度の詳細 ±2 °C(±3.6 °F)露点
  • 応用例 空気, エアドライヤー, 化学精製所, クリーンルーム, クリーンウォーターと浄化溶液, コンプレッサー制御, フィルター監視, 流量測定, ガス, HVAC, 産業および製造業, 天然ガスコンプレッサー, 発電所とボイラー, 研究開発/エンジニアリング試験, 冷蔵, 冷蔵設備, 温度維持, 廃水の応用
  • 校正に関する注記 トレーサブル13点校正証明書
  • 補償温度、最大 50 °C
  • 補償温度、最小 -20 °C
  • コンプライアンスに関する注意事項 ATEX/UKCA: II 1 G Ex ia IIC T4 Ga (-20~+70 °C) IECEx: EX ia IIC T4 Ga (-20~+70 °C) TR CU @ 0Ex ia IICT4 Ga (-20~+70 °C) cQPSus: Class I, Division 1, Groups A, B, C & D, T4 Class I, Zone 0, AEx ia IIC T4 Gb, Ex ia IIC T4 Gb Tamb +70 °C
  • 寸法に関する注意事項 MiniDIN 43650 フォームC L=132mm x ø45mm(コネクターケーブル付き)
  • 電気接続 Mini DIN 43650 C
  • 電気出力 0~20 mA
  • エンクロージャーの定格 IP66, NEMA タイプ 4
  • 工場出荷時設定 センサー故障:23 mA;アンダーレンジ露点:4 mA;オーバーレンジ露点:20 mA
  • 流量に関する注記 標準サンプリングブロックに取り付けられた1~5 Nl/min;直接挿入式で0~10 m/sec
  • ガルバニック絶縁 KFD2-CR-EX1.20200,KFD2-CR-EX1.30200,KFD0-CS-EX1.50P,KFD0-CS-EX2.50P,KFD2-STC4-EX1.H,MTL5041,MTL5040
  • 高さ 132 mm
  • ハウジング材質 316ステンレス鋼
  • 長さ 45 mm
  • 荷重抵抗 最大250 Ω @ 14 V(500 Ω @ 24 V)
  • 動作圧力(最大) 52.5 MPa
  • 動作温度(最高) 60 °C
  • 動作温度(最低) -40 °C
  • プロセス接続サイズ 5/8インチ
  • プロセス接続タイプ UNF オス
  • 繰り返し精度 0.5°C(0.9°F)露点
  • 応答時間 5分でT95(乾燥から湿潤へ)
  • シリーズID EA2-TX
  • 最大保管温度 60 °C
  • 保管温度(最低) -40 °C
  • 供給電流 23 mA
  • 供給電圧 12から28Vdc
  • 重量 150 g

Supported Applications

The EA2-TX Series is the Easidew 2-wire dew-point transmitter from Michell Instruments, a compact loop-powered instrument for measuring moisture content in gases. Delivering its reading as a standard current signal, it installs directly into a process line or sample block and reports dryness continuously to a controller, PLC, or monitoring system.

It is well suited to natural gas, hydrogen, nitrogen, air, and inert gas systems, and to compressed-gas drying where product quality depends on low moisture. A choice of process connections and electrical connectors makes the EA2-TX straightforward to fit into new or existing sampling arrangements for reliable, long-term dew-point monitoring.

Operating Conditions & Performance

The transmitter measures dew point over -110 to +20°C (-166 to +68°F), with a companion range of -100 to +20°C (-148 to +68°F), resolving readings to 0.01 °C. It holds an accuracy of ±0.5 °C / ±0.9 °F with a repeatability of ±0.2 °C, and provides a typical T90 response of less than 10 seconds.

Output is a 4–20 mA loop signal with RS485 / Modbus RTU communications, powered from 10–30 VDC into a load of up to 500 Ω at 24 VDC, terminated through a DIN 43650 or M12 connector. The sensor withstands pressures up to 45 MPa (450 barg / 6500 psig), and its wetted parts use 316L stainless steel with an HMWPE guard.

The EA2-TX carries an IP67 enclosure and operates over a process range of -100 °C to +100 °C, an ambient range of -40 °C to +85 °C, and storage to -40 °C to +85 °C. The probe measures 12 mm in diameter with a 25 mm insertion length, a 50 mm stem, and a 100 mm overall length. Approvals include ATEX, IECEx, UL, CSA, and NEC.

Configuration Options

The EA2-TX is ordered as a configured transmitter, with a simplified alphanumeric code that fixes each feature to the application. The configurable axes are:

  • Range — a -100 to +20°C or -110 to +20°C dew-point range, or a non-standard configured range in °C, °F, or ppmV.
  • Protection — a standard HDPE guard against fine particulates, or a stainless-steel sintered guard.
  • Oxygen cleaning — standard, or cleaned for oxygen service, which is offered only with the stainless-steel sintered guard.

The choices that most change the delivered instrument are the guard type and oxygen-cleaning selection, which together govern particulate protection and suitability for oxygen-enriched media, while the range option sets the span over which the transmitter is scaled.

Key Product Differences

Ordering follows the parent code and its three feature positions, EA2-TX - <Range> - <Protection> - <Oxygen Cleaning>. The lineup spans the letter combinations from EA2-TX-AAA through EA2-TX-BBB, for example:

  • EA2-TX-ABB — Easidew 2-wire transmitter with the -100 to +20°C range, a stainless-steel sintered guard, and oxygen-cleaned wetted parts.
  • EA2-TX-RAA — non-standard range built to customer specification with an HDPE guard and no oxygen cleaning; the range is specified at time of order.

Under the previous ordering system the same choices were written out longhand, for example EA2-TX+(-100/+20C)+HD for the base transmitter with the -100 to +20°C range and an HDPE guard. Across every configuration the core sensing platform is unchanged — the model number simply records the chosen range, guard, and oxygen-cleaning options.

ja-JP
ja_JP
設定を保存する