검색으로 이동 메인 콘텐츠로 이동 탐색으로 이동

한국 1588-8983 | 새로운 웹사이트에 오신 것을 환영합니다. 문제나 버그를 발견하셨나요? 여기에 보고해주세요

현재 에 계신 것을 확인했습니다. 아래 링크를 클릭하여 지역 사이트를 방문하시면, 지역별 특가 혜택과 지원 서비스를 받으실 수 있습니다.

Series-SCD

DINレール PID 温度/プロセスコントローラー、ユニバーサル入力、リレー出力、ワイヤレス

  • 1から8まで拡張可能なプロセス制御ループ
  • ユニバーサルトランスミッターまたは温度センサー入力
  • RS-485 Modbus®通信
  • デュアルループまたはシングルループ/アラーム出力制御
Series-SCD
시작 ¥ 20,851
DINレール PID 温度/プロセスコントローラー、ユニバーサル入力、リレー出力、ワイヤレス Series-SCD Series-SCD
loading all models
제품 개요
  • 応用例 熱・エネルギーシステム, HVAC
  • 制御出力 SPSTリレー
  • データインターフェース RS-485 Modbus ASCII/RTU
  • 入力制御信号 0から20 mA
  • 入力タイプ 熱電対、RTD、直流電圧または直流電流
  • メモリバックアップ 非揮発性
  • 取付方向 DINレール
  • 動作温度(最高) 122 °F
  • 動作温度(最低) 32 °F
  • 出力ノート リレー: 3 A @ 250 Vac 抵抗負荷
  • 出力タイプ (B) リレー
  • 消費電力 3 W
  • RTD入力範囲 JPt 100: -4~752 °F; Pt 100: -328~1562 °F; Ni 120: -112~572 °F; Cu 50: -58~302 °F
  • シリーズID Series-SCD
  • 電源タイプ DC
  • 供給電圧 24 Vdc
  • スイッチ定格 3 A @ 250 VAC
  • 温度センサーの種類 RTDまたは熱電対
  • 熱電対入力範囲に関する注記 タイプK: -328~2372 °F; タイプJ: -148~2192 °F; タイプT: -328~752 °F; タイプE: 32~1112 °F; タイプW: -328~2372 °F; タイプR: 32~3092 °F; タイプS: 32~3092 °F; タイプB: 212~3272 °F; タイプL: -328~1562 °F; タイプU: -328~932 °F
  • 電圧入力範囲 0から5V、0から10Vまで
  • 重量 2.7 oz

Supported Applications

The Dwyer Series SCD DIN Rail PID Temperature/Process Controllers are microprocessor-based regulating devices designed for heating and cooling applications. These controllers function as master (SCD-1000) or slave (SCD-2000) units within a multi-loop system, where one master controller can be combined with up to seven slave controllers without additional wiring between them.

While primarily configured for temperature regulation using thermocouples and RTDs, the series supports universal inputs including DC linear voltage and current signals. The product overview notes that in specific configurations involving carbon monoxide transmitters (such as Dwyer GSTA or CMT200 series), the SCD controller can accept signal input to adjust set points for fan/damper operation and high gas concentration alarms, typically around 25 PPM with a high alarm near 100 PPM. For systems requiring integration with building management infrastructure, the controllers provide feedback of current process values, set points, and output status via RS-485 Modbus® communication.

Operating Conditions & Performance

The Series SCD operates within an ambient temperature range of 32 to 122°F (0 to 50°C). The controllers are designed for installation completely within a panel or process control enclosure, requiring a separate UL Listed enclosure. Power is supplied via isolated switching power at 24 VDC.

Performance specifications include the following measurement capabilities:

  • Sensor Inputs: Thermocouple types K, J, T, E, N, R, S, B, L, U, and TXK; Platinum RTD (Pt100, JPt100); Linear DC inputs of 0–5V, 0–10V, 4–20mA, 0–20mA, and 0–50mV.
  • Sampling Rate: Analog input at 0.15 sec; Thermocouple or Platinum RTD at 0.4 sec.
  • Control Methods: PID, ON/OFF, Manual, and PID program control.

The controllers feature non-volatile memory backup to retain settings during power interruptions. For DC current input applications, a 250 Ω precision resistor is required as an accessory.

Configuration Options

Each controller in the series includes one universal input and two output groups: one relay output (standard) and one user-selectable auxiliary output. The available configurations are defined by the model number suffix:

  • Master Controllers (SCD-10xx): SCD-1023, SCD-1033, SCD-1053, and SCD-1063.
  • Slave Controllers (SCD-20xx): SCD-2023, SCD-2033, SCD-2053, and SCD-2063.

The auxiliary output options include:

  • Voltage Pulse (Code 2): DC 12V with a maximum output current of 40 mA.
  • Relay Output (Code 3): SPST, rated for 3 A @ 250 VAC resistive load.
  • Current Output (Code 5): DC 4–20mA with a maximum load resistance of 5,000Ω.
  • Linear Voltage Output (Code 6): 0–10 VDC with a minimum load resistance higher than 1,000Ω.

The linear voltage and current outputs can function as control output, alarm output, or retransmission output. The series supports RS-485 digital communication using the Modbus® RTU/ASCII protocol at baud rates from 2,400bps to 38,400bps.

Key Product Differences

The Series SCD distinguishes between Master and Slave units based on their role in a multi-loop configuration. The SCD-1000 series serves as the master controller (first position), while the SCD-2000 series functions as slave controllers installed in parallel, allowing up to seven slaves per master without external wiring for power or communication between them.

Model variations are further defined by the auxiliary output type selected. For example, models ending in "3" (e.g., SCD-1023) feature a relay as the second output group, whereas models ending in "5" provide a 4–20mA current loop and those ending in "6" offer a 0–10V linear voltage signal. All variants share identical physical dimensions of approximately 90 mm (H) x 60 mm (W) with DIN rail mounting capability.

Compliance certifications for the series include CE and cULus LISTED. Accessories such as the SCD-PS power supply, MN-1 USB/RS-485 converter, A-277 precision resistor, and SCD-SW configuration software are available to support installation and operation.

액세서리

100~240 VAC/VDC를 24 VDC로 변환하는 전원 공급 장치.
70,321원 / 개당
0 재고 있음

accessories

Precision resistor, 250 ohm
20,473원 / 개당
0 재고 있음
R/C snubber (recommended for inductive loads like a solenoid or contactor)
43,173원 / 개당
0 재고 있음

signal conditioners

171,833원 / 개당
0 재고 있음
ko-KR
ja_JP
설정 저장