검색으로 이동 메인 콘텐츠로 이동 탐색으로 이동

한국 1588-8983 | 새로운 웹사이트에 오신 것을 환영합니다. 문제나 버그를 발견하셨나요? 여기에 보고해주세요

현재 에 계신 것을 확인했습니다. 아래 링크를 클릭하여 지역 사이트를 방문하시면, 지역별 특가 혜택과 지원 서비스를 받으실 수 있습니다.

SAP-RTD-Series

접착 패드 RTD 센서

粘着パッドRTDセンサー
  • 優れた柔軟性を持つシリコーンゴム製
  • 応答時間を短縮する自己粘着性の薄型裏地
  • 正確な温度測定のため、清潔な表面に直接貼り付け可能
  • 自己粘着パッドにより一度だけ表面に設置可能
SAP-RTD-Series
시작 ¥ 17,438
粘着パッドRTDセンサー SAP-RTD-Series SAP-RTD-Series
loading all models
제품 개요
  • 精度 クラス A
  • 電気接続 被覆除去済みリード線
  • 絶縁 PFA
  • 名目抵抗 100 Ω
  • ワイヤ本数 4
  • パッド材質 シリコン
  • プロセス温度(最高) 200 °C
  • プロセス温度(最低) -50 °C
  • シリーズID SAP-RTD-Series
  • 温度センサーの種類 RTD
  • 線径 24 AWG

Supported Applications

The Omega SAP-RTD-Series consists of adhesive pad RTD sensors designed to take surface temperature measurements. These self-adhesive silicone pads are intended for use on both flat and curved surfaces. Documented applications include hot plate measurements, pipe measurements, and direct connection to instrument casings or motor housings to obtain accurate temperature readings.

Operating Conditions & Performance

The series operates within a measurement range of -50 to 200°C (-58 to 392°F). The sensing element is a 100 Ω Platinum RTD configured with 4-wire leads. Construction features an integral RTD element bonded onto the inner surface of exposed silicone material, which provides faster temperature response compared to non-bonded configurations.

Configuration Options

The SAP-RTD-Series is configurable across pad designations, wire lengths, and termination styles. The series supports two primary mounting geometries:

  • SAPC: Pad for curved surfaces (0.59 X 1.97 X 0.29 in / 15 x 50 x 7.4 mm).
  • SAPF: Pad for flat surfaces (1.41 x 0.48 x 0.29 in / 35 x 12 x 7.4 mm).

Standard wire lengths are available at 40, 80, and 120 inches, with other lengths offered as options. The lead wire is PFA-coated, 24 AWG. Termination defaults to stripped ends, though connector options are available.

Model Number Configuration

The series follows a specific model number guide: <PAD DESIGNATION> - <RTD TYPE> - <WIRE CONFIGURATION> - <ELEMENT RESISTANCE> - <TERMINATION> - <WIRE LENGTH>. An example configuration is SAPC-RTD-4-100-A-80, representing a self-adhesive silicone RTD sensor with 100 Ω resistance and 80 inches of PFA-coated lead wire.

Key Product Differences

Variants within the series are distinguished by pad geometry (SAPC for curved surfaces versus SAPF for flat surfaces) and standard or custom wire lengths. All variants utilize a silicone rubber housing material with an adhesive backing for surface mounting. The electrical configuration remains consistent across the family as a 100 Ω Platinum RTD with 4-wire leads.

ko-KR
ja_JP
설정 저장