1-800-663-4209 | Welcome to our new website, found an issue or bug? Please report it here
DP20-Series
Panel Meter - 1/8 in DIN, Temperature, Process
Models In Stock
DP20-Series
From
C$
229.58
Models In Stock
Product Overview
Show Ratings & Reviews
Rated 4 out of
5
by
Bob52 from
Nice meter for the price
My application was to display rpm on a mill, where the speed control produced a 0-10v signal that corresponded to 0-4500 rpm. The DP20 was easy to program for that use and works well. Be aware the case is very thin, and the clamps are plastic so it's not as robust as you might be used to.
Date published: 2018-04-15
Rated 4 out of
5
by
wstein25 from
Does the job but ...
I may be a bit dense about these things, but I found the nested menu/push button configuration complicated. In the end I got the scaling and alarms set up as I needed, but I'm not sure I could explain how I did this. But, in the end it works well as advertised.
Date published: 2018-05-06
Rated 5 out of
5
by
ruf tech from
good display
liked the easy installation. easy to program with only three buttons. easy to see display from a distance. the plastic bracket was a bit flimsy but it did the job.
Date published: 2021-02-08
Rated 4 out of
5
by
Nick I from
Good value part
Decent quality for the cost. Relays are a nice addition.
Date published: 2021-02-04
Rated 4 out of
5
by
scn01 from
works good great value
setup was a small challenge but meter worked as described and has a bright display
Date published: 2018-01-16
Rated 5 out of
5
by
undisclosed from
great product, works as advertised
great product, works as advertised, priced appropriately
Date published: 2024-09-20
Rated 5 out of
5
by
Angela Clark from
Customer Service Specialist
Super fast quoting and super fast shipping. Parts are always in stock.
Date published: 2024-05-21
Rated 5 out of
5
by
Wm Ed from
Panel Meter
I found just what I was looking for with the Omega Engineering DP20-M1 panel meter. Simple installation and easy to configure. For support, Omega Engineering has a very good manual online for this unit which is great.
Date published: 2024-03-21
we have this controller hooked to a PX119-1K. We have set the scale to D.Lo to 0 and D.Hi to1000. unit still reads -250. we have gone through the manual many times and set it up both ways for 4-20mA. - Please help
Assuming you are using the internal excitation on-board the DP20. Jumper "S" on the PCB should be on position "D" Jumper "T" should be bridging pins 1 & 2. The positive lead from the sensor should be on Term# 5 of the Input terminal block. The negative lead should be on Term#2. Verify that you have the 15VDC excitation be measuring between terminals 5 and 4 with a DC voltmeter. Make sure you are choosing Process input and 4/20 mA range.
Date published: 2023-02-13
Do you sell the small Blue retainer clicks separately? Our had gotta brittle and the meter doesn't mount well. If you do, please post a part number. Thanks Jeff at Teledyne Marine.
Thank you for your inquiry. Please send your request to sales@omega.com
Date published: 2020-05-18
Hi, I have an omega DP20 meter, question, is it a need to drop a transient voltage suppressor across my signal inputs to protect against voltage spikes or is the DP20 capable of handling such an occurrence? Thanks
Thank you for your inquiry. Voltage Suppressor is not required for voltage input signals.
Date published: 2022-05-20
I have a failed NEWPORT IDP-0/E and was wondering if this would be an equivalent replacement when used with an input of 4-20 mA. Meter is only used to display values. Also can this be used outdoor exposed enclosure?
Thank you for your inquiry. The DP20 would have to be in a weatherproof enclosure to ensure long-lasting use.
Date published: 2020-12-04
I can't seem to figure out how to scale the signal to have numbers AFTER the decimal point. I am using an externally powered PX119 set up for 4-20mA. I am measuring psi from 0-30, and I would like the display to read 9.45 psi rather than just 9 or .09 etc
Dear AdamB, thank you for contacting Omega Engineering. For scaling the DP20 to read from 0.00 through 30.00 psi, assuming you have the wiring and the internal jumpers correct, keep pressing the little square button, till you see "SCAL" , you will see DP (Decimal Point) : Set the decimal point in the middle, so XX.XX . Your D.Lo should be 00.00 and D.Hi should be 30.00. You should then be reading from 00.00 to 30.00.
For more information please see page 19 of the manual: https://assets.omega.com/manuals/M5668.pdf
Date published: 2023-02-03
I am using this with thermocouples, is the meter calibratable?
Thank you for your inquiry. This unit is not calibratable.
Date published: 2024-03-22
I see that there is a place for "units". Is this digital that needs to be programmed? Or is this just a label, and does it come with a sheet of labels? I will be needing RPM and Amps
Thank you for your inquiry. This device does not display units of measure digitally. It is the user responsibility to interpret the units of the value displayed.
Date published: 2023-09-28
Can the relays switch DC? The manual only mentions up to 250VAC. I would be switching 24VDC
The only rating for the relays on the DP20 is for 250 VAC at 8 amps. There is not any DC Voltage rating.
Date published: 2020-12-10