1-800-663-4209 | Bienvenue sur notre nouveau site Web, vous avez rencontré un problème ou un bug? Veuillez le signaler ici
DP7600-Series
Mètres de charge/de déformation à haute vitesse et voltmètres de processus
Modèles en stock
- 5-Digit Display
- Dual Inputs Available
- All Programming and Calibrating Via 5 Front Panel Switches
- Programmable Digital Filter, 1 to 500 Hz Cutoff
DP7600-Series
Depuis
C$
1 853.91
Modèles en stock
L'aperçu du produit
- Précision ± 0.01 %
- Détail de la précision ± 0.01% of reading ± 1 count of A/D @ 25°C (77°F)
- Channels One channel standard, second channel optional
- Convert/Hold Input Normally high; if pulled low, holds display
- Cutout Dimensions 2.45 x 5.06 in
- Digital Filter Programmable Cutoff Frequency
- Display Note -32768 to 32767 with programmable decimal points; 14 mm (0.56") red LED
- Display Type LED
- Electrical Connection Screw Terminal
- Form factor 1/8 DIN
- Height 2.7 in
- Input Analog Filter 4-pole active anti-alias; 500 Hz cutoff on single-channel unit and 250 Hz cutoff on dual-channel unit
- Input Bias Current ± 50 nA maximum ± 100 pA/°C (per input channel)
- Input Configuration Front Keypad
- Internal Resolution 16 bit
- Length 6.9 in
- Measurement Type Current, Strain, Voltage
- Mounting Panel
- Number of Digits 5
- Number of Inputs 1
- Operating Temperature, Max 60 °C
- Operating Temperature, Min -20 °C
- Output Method RJ11 jack for serial interface
- Peak Detection Updated at rate selected by digital filter, peak stored in memoryrogrammed to give limit #1 output up to 100 seconds after a programmed limit is reached. This output can be used to reset the peak reading by tying limit #1 output to remote input
- Power Consumption 8 W
- Reading Rate Limited to 1000/s divided by number of channels
- Remote Inputs Display Peak, Display Runout, Reading, Reset Peak, Runout Reading, Tare
- Resolution 16-bit A/D
- Rollover Error ± 2 counts of A/D @ 25°C (77°F)
- Runout Mode Updated at rate selected by digital filter. Runout is normally stored in memory and recalled via front-panel switch, over the serial interface, or by selecting runout display mode on rear connector.
- Sampling Rate 1000 Hz
- Sensor Excitation ± 15 Vdc, ± 5 Vdc @ ± 50 mA
- SetPoint Outputs 4 isolated open collector transistor outputs rated 30 Vdc maximum; will sink up to 50 mA; 300 V isolation between limit outputs and system ground; limit #1 can be programmed to be delayed from 1 to 100 seconds
- Settable Parameters Digital Filter, Limits, Offset, Span
- Weight 370 g
- Width 5.18 in
The DP7600 is a high speed load/strain meter. The unit performs 1000 conversions per second with limit checking and peak/runout tracking done at a user selectable rate (from 1 to 500 Hz). Peak and runout data can also be displayed using the front panel switches. A tare reading, up to 50% of span, can be entered with a single front panel push button.
The DP7700 is a high speed process/voltmeter with many of the same features. The DP7700 accepts most process inputs from 0-200 mV to 0-10 Vdc and 4-20 mA current loops. Transducer/loop power of ± 15 Vdc @ 50 mA is standard.
Programming both meters is accomplished via five switches located on the front panel. The text at the top of the switch (NORMAL, PEAK, RUNOUT, TARE, ABS/REL) indicates its normal function. The text at the lower half of the switch (ENTER, UP, DOWN, NEXT, EXIT) indicates the switch’s function during setup and calibration.
The DP7700 is a high speed process/voltmeter with many of the same features. The DP7700 accepts most process inputs from 0-200 mV to 0-10 Vdc and 4-20 mA current loops. Transducer/loop power of ± 15 Vdc @ 50 mA is standard.
Programming both meters is accomplished via five switches located on the front panel. The text at the top of the switch (NORMAL, PEAK, RUNOUT, TARE, ABS/REL) indicates its normal function. The text at the lower half of the switch (ENTER, UP, DOWN, NEXT, EXIT) indicates the switch’s function during setup and calibration.
PDF et manuels
Afficher les notes et les avis