1-800-663-4209 | Welcome to our new website, found an issue or bug? Please report it here
FP3-5200
Stainless Steel Paddlewheel Flow Meter
Models In Stock
- Stainless Steel Paddle Wheel Sensors
- Boiler Water Feed Lines
- Turbine Steam Condensate
- Energy Management Systems, HVAC
FP3-5200
From
C$
1,163.52
Models In Stock
Product Overview
- Accuracy ± 0.2 ft/s
- Cable Length 25 ft
- Cable Length Note 7.5 m (25'), can be extended up to 30 m (100') with copper wire
- Electrical Output Sine Wave
- Impedance 10 kΩ
- K-Factor 12 Hz/fps
- Linearity Error ±1%
- Material Construction Option N/A
- Materials, Wetted 316 Stainless Steel, 347 Stainless Steel, CD4MCu Stainless Steel, Fluoroloy B, Tungsten Carbide
- Media Compatibility Liquids
- Media Compatibility Note 10%, with particulate size not exceeding 5 mm cross section or length
- Mounting Orientation N/A
- Operating Pressure, Max 1500 psi
- Operating Pressure, Min 0 psi
- Output Detail 12 Hz per ft/sec, 80 mV peak-to-peak per fps nominal
- Pipe Connection Note Mini Tap
- Measurement Pressure Type Gauge
- Process Connection Size 1/2 in
- Process Connection Type NPT Female
- Repeatability Error ±0.5%
- Supply Current 10 mA max
- Supply Power Note 5 to 24 Vdc @ 10 mA maximum
- Supply Voltage 5 to 24 Vdc
- Velocity, Max 20 ft/s
- Velocity, Min 1.6 ft/s
- Viscosity Note 1 Centipoise (water); up to 5 cp above 5 fps velocity
- Viscosity Range 5 cPs
- Weight 0 kg
ACCURACY THAT PAYS OFF
In the FP-5200 sensor housing, a magnet is surrounded by a coil, creating a magnetic field. As the liquid flow causes the rotor to spin, each blade passing this coil concentrates the lines of magnetic force, producing a repeatable AC sine wave output. The FP-5200 also features OMEGA’s patented "open-cell" rotor, for increased linearity at ±1% over the full dynamic range of 1.6 to 20 fps, with negligible head loss.
COMPATIBLE, VERSATILE INTERFACING
The FP-5200 is completely compatible with FPM Series powered flow indicators, controllers, and totalizers, to give increased flexibility in system design. It also interfaces easily with digital computers and with a variety of other external equipment.
FP-5200 FLOW SENSOR
When you're looking for the added strength of an all-metal flow sensor, make it the FP-5200. It permits the high degree of accuracy and reliability you demand, without added cost. Compare it to traditional metal flowmeters, where the price increases dramatically with pipe size. In contrast, you can install the FP-5200 insertion flow sensor in pipe sizes ranging from ½ to 12" without a lot of additional cost, because the sensor price increases only slightly for larger pipe sizes. Furthermore, it's accurate to ±1% of full scale. Installation is easy. Use the FP-5200 locally, or in a remote area up to 100 feet from the meter or controller without signal amplification. It needs no external power or battery. Just one operator, simple tools, an FP-5200 Flow Sensor, a few minutes . . . and you're on-line. Additionally, the all-stainless-steel flow sensor accurately measures a wide variety of fluids, even under high pressure and temperature conditions [pressures up to 1500 psi, temperatures up to 150°C (300°F)].
METAL HOT-TAP FLOW SENSOR
The metal hot-tap sensor allows the user easy sensor installation and removal without shutting down the process stream. Compatible with Mueller drill assemblies, this new hot-tap sensor can be quickly installed into pipe sizes from 1½ to 24". This hot-tap assembly is compatible with any 1½ NPT female pipe fitting such as weldolets and saddles. Installation fitting not supplied.
In the FP-5200 sensor housing, a magnet is surrounded by a coil, creating a magnetic field. As the liquid flow causes the rotor to spin, each blade passing this coil concentrates the lines of magnetic force, producing a repeatable AC sine wave output. The FP-5200 also features OMEGA’s patented "open-cell" rotor, for increased linearity at ±1% over the full dynamic range of 1.6 to 20 fps, with negligible head loss.
COMPATIBLE, VERSATILE INTERFACING
The FP-5200 is completely compatible with FPM Series powered flow indicators, controllers, and totalizers, to give increased flexibility in system design. It also interfaces easily with digital computers and with a variety of other external equipment.
FP-5200 FLOW SENSOR
When you're looking for the added strength of an all-metal flow sensor, make it the FP-5200. It permits the high degree of accuracy and reliability you demand, without added cost. Compare it to traditional metal flowmeters, where the price increases dramatically with pipe size. In contrast, you can install the FP-5200 insertion flow sensor in pipe sizes ranging from ½ to 12" without a lot of additional cost, because the sensor price increases only slightly for larger pipe sizes. Furthermore, it's accurate to ±1% of full scale. Installation is easy. Use the FP-5200 locally, or in a remote area up to 100 feet from the meter or controller without signal amplification. It needs no external power or battery. Just one operator, simple tools, an FP-5200 Flow Sensor, a few minutes . . . and you're on-line. Additionally, the all-stainless-steel flow sensor accurately measures a wide variety of fluids, even under high pressure and temperature conditions [pressures up to 1500 psi, temperatures up to 150°C (300°F)].
METAL HOT-TAP FLOW SENSOR
The metal hot-tap sensor allows the user easy sensor installation and removal without shutting down the process stream. Compatible with Mueller drill assemblies, this new hot-tap sensor can be quickly installed into pipe sizes from 1½ to 24". This hot-tap assembly is compatible with any 1½ NPT female pipe fitting such as weldolets and saddles. Installation fitting not supplied.
Accessories
accessories
consumables
installation hardware
sensors
Show Ratings & Reviews